Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterChimney Cleaning in Haltom City, TX
Chimney cleaning in Haltom City costs $169-$289 for a standard sweep and runs higher when a camera inspection or creosote removal is added. What makes Haltom City jobs different is the housing stock: most of these brick ranch homes were built between 1952 and 1975, and many still carry their original clay tile flue liners, now 50 to 70 years old. A sweep here almost always doubles as a structural safety check, because the liners in this part of Tarrant County fail at a rate you simply don’t see in the newer subdivisions a few miles north. Call (980) 580-8641 and we’ll quote the job in writing before anyone picks up a brush.
Why Haltom City Homes Are Different
Haltom City is one of the oldest inner-ring suburbs in Tarrant County, with a housing stock dominated by post-WWII brick ranch homes built between the early 1950s and mid-1970s. The original masonry chimneys on these homes, many never professionally serviced, now carry clay tile flue liners that are 50-70 years old. That’s precisely the age range when spalling, cracking, and mortar joint failure become common, so chimney cleaning in Haltom City regularly uncovers structural issues that a routine sweep in a newer city wouldn’t.
North Texas winters are short and mild most years, so Haltom City homeowners use their fireplaces infrequently. But events like the February 2021 Winter Storm Uri drive sudden, heavy fireplace use that accelerates creosote buildup in chimneys that may have sat dormant for years. The region’s freeze-thaw cycles, though infrequent, are severe when they occur and aggressively crack the mortar crowns and joints on the area’s aging masonry chimneys.
A disproportionate share of Haltom City’s 1950s and early 1960s homes were built before Texas adopted standardized flue sizing and liner requirements. Sweeps here regularly uncover fireplaces with undersized or effectively unlined flues, a hazard that only surfaces during a thorough cleaning and inspection, and one far more common in Haltom City than in the newer subdivisions just a few miles north.
Our Main Haltom City Services
Two services get the most calls from Haltom City homeowners: fireplace work tied to these older masonry fireboxes, and cap and crown replacements on chimneys that have taken fifty years of North Texas weather.
Fireplace Services in Haltom City
Many Haltom City fireplace problems trace back to the same root: a firebox built in the 1950s or 1960s that has never been evaluated against current clearances and materials. Smoke backing into the room, cracked refractory panels, or a damper that won’t seal are common on the original builder-grade fireplaces throughout the city. We inspect the firebox, throat, damper, and surround before recommending any repair, and you get photos of every condition we find. If your fireplace has been acting up, see Fireplace Services in Haltom City for the full breakdown.
Chimney Cap & Crown in Haltom City
The mortar crowns on Haltom City’s 1950s and 1960s chimneys were poured thin and often without expansion joints. Fifty-plus years of freeze-thaw cycles later, they crack and let water into the brick and mortar below. A rusted or missing cap makes it worse. We replace crowns with properly sloped concrete and install caps sized to the flue. Details and pricing are on the Chimney Cap & Crown in Haltom City page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterChimney Sweep in Haltom City
A chimney sweep in Haltom City usually costs $169-$289, and that work is about more than soot removal. Most homes here were built between 1952 and 1975 with original clay tile liners, and a sweep brings us face to face with whatever fifty or sixty years of use and North Texas weather have left inside. Our standard job includes a camera-scan inspection under NFPA 211 Level 2 guidelines, so you see exactly what we see. The full detail on method and materials is on our Chimney Sweep hub page.
Level 1 Inspection
Signs you need it
You use your fireplace regularly and want confirmation that the flue is clear and safe before burning season.
What it costs in Haltom City
A Level 1 inspection in Haltom City runs $99-$180 and is included with most standard sweeps.
How we do it
We check the accessible portions of the chimney, flue, and appliance connections without removing any structure.
Level 2 Inspection
Signs you need it
You’ve had a chimney fire, a house fire, a weather event like Winter Storm Uri, or you’re buying or selling a home.
What it costs in Haltom City
A Level 2 inspection in Haltom City runs $199-$350 and includes camera scanning of the flue interior.
How we do it
We run a camera from the firebox to the flue crown and document every liner crack, joint separation, and obstruction.
Creosote Removal
Signs you need it
Your damper is sticky, you smell a sharp burnt odor near the fireplace, or it’s been more than a year since your last cleaning.
What it costs in Haltom City
Creosote removal in Haltom City runs $149-$300 depending on whether the buildup is Class I, II, or III.
How we do it
We identify the creosote class on camera, then use rotary loops or chemical treatment matched to the specific grade.
Soot Removal
Signs you need it
Black dust is visible around the fireplace opening or the firebox walls feel soft and flaky to the touch.
What it costs in Haltom City
Soot removal in Haltom City runs $129-$199 and usually accompanies a standard sweep.
How we do it
We brush the flue walls and vacuum the firebox and smoke chamber with a HEPA-filtered unit so nothing blows back into the room.
Annual Sweep
Signs you need it
It’s been 12 months or more since the last sweep, or you’re about to start burning regularly after a long dormant stretch.
What it costs in Haltom City
An annual sweep in Haltom City runs $169-$289 and includes the camera-scan inspection at no added charge.
How we do it
We cover the firebox opening, run a correctly sized brush through the flue, then sweep and vacuum the firebox, damper, and smoke chamber.
What Chimney Sweep Costs in Haltom City
| Item | Typical range in Haltom City |
|---|---|
| Level 1 Inspection | $99-$180 |
| Level 2 Inspection with camera scan | $199-$350 |
| Standard sweep with inspection | $169-$289 |
How often should a chimney be cleaned in Haltom City?
Once a year if you burn more than a dozen fires a season. Homes that sat dormant before a hard-use winter like 2021 should be inspected before lighting the first fire. Call (980) 580-8641 for an exact quote.
What actually happens if I skip a cleaning in Haltom City?
Creosote builds up along the flue walls and can ignite at a temperature far lower than most homeowners realize. In a 60-year-old clay liner, a chimney fire can spread into the house structure. Call (980) 580-8641 and we’ll inspect before you burn.
Chimney Repair in Haltom City
Chimney repair in Haltom City is usually a mortar problem before it’s anything else. These 1950s and 1960s masonry chimneys were built with lime mortar that breaks down under decades of freeze-thaw cycles, and the bricks and crowns start moving soon after. Our repair scope always begins with a camera-scan inspection so there’s photographic proof of what’s broken before anything gets quoted. Full repair detail lives on our Chimney Repair hub page.
Mortar Repointing
Signs you need it
Mortar joints have eroded more than a quarter inch, or you can scrape out crumbling mortar with a flathead screwdriver.
What it costs in Haltom City
Repointing in Haltom City runs $35-$55 per square foot of masonry surface.
How we do it
We grind out the failed joints to a consistent depth and pack in fresh mortar matched to the original texture and color.
Spalling Brick Repair
Signs you need it
Brick faces are flaking, popping off, or leaving rust-colored dust on the hearth or roofline.
What it costs in Haltom City
Spalling brick repair in Haltom City runs $700-$2,500 depending on how many bricks need replacement.
How we do it
We cut out the damaged brick, match the size and color from local masonry suppliers, and install each replacement with proper bed joint mortar.
Chimney Waterproofing
Signs you need it
You see efflorescence, a white chalky residue, on the brick inside or out, or water stains on interior walls near the chimney.
What it costs in Haltom City
Chimney waterproofing in Haltom City runs $250-$600 for a full exterior application.
How we do it
We apply a vapor-permeable silane-siloxane water repellent that keeps rain out but lets moisture inside the brick escape.
Flashing Repair
Signs you need it
Water is getting in at the roofline, or the existing flashing is rusted, lifted, or missing sections.
What it costs in Haltom City
Flashing repair or replacement in Haltom City runs $450-$1,400 depending on roof pitch and chimney footprint.
How we do it
We remove the old flashing, cut and bend new step and counter flashing from aluminum or copper, and seal every seam.
What Chimney Repair Costs in Haltom City
| Item | Typical range in Haltom City |
|---|---|
| Mortar repointing | $35-$55 per square foot |
| Spalling brick repair | $700-$2,500 |
| Chimney waterproofing | $250-$600 |
Do I need a permit for chimney repair in Haltom City?
Most repointing and minor repair work doesn’t require a permit, but structural changes or a full rebuild may. We handle permit research as part of the written scope. Call (980) 580-8641 for specifics on your address.
Can damaged mortar really be fixed, or do I need a rebuild?
Repointing fixes damaged joints provided the brick itself is still sound. If the masonry has shifted or the firebox is compromised, a partial rebuild is safer. We’ll show you camera footage before a recommendation is made. Call (980) 580-8641.
Chimney Liner & Rebuild in Haltom City
Chimney liner work in Haltom City lands differently here because so many pre-1960s homes were built before Texas standardized flue sizing. We regularly find undersized clay tile liners or effectively unlined flues during what starts as a routine cleaning. A stainless steel liner solves the safety problem without a full rebuild, and our camera record shows you exactly why the work is needed before you spend a dollar. Materials and method details are on our Chimney Liner & Rebuild hub page.
Stainless Steel Liner
Signs you need it
The existing clay liner is cracked, spalling, or separated at the joints, or the flue was never properly lined.
What it costs in Haltom City
A stainless steel liner in Haltom City runs $2,500-$5,500 installed, including the connecting hardware.
How we do it
We size the liner to the appliance and flue dimensions, then run it from the firebox through the crown and secure it at the top plate.
Flexible Liner
Signs you need it
The flue has an offset or irregular shape that a rigid liner can’t follow without removing masonry.
What it costs in Haltom City
A flexible liner in Haltom City runs $2,500-$5,000 installed and is often the fastest solution for older flues.
How we do it
We pull the flexible liner through the existing flue path, following the contours of the original masonry, and connect it to the appliance collar.
Liner Replacement
Signs you need it
Camera inspection shows cracks wider than a hairline, missing tile sections, or collapse debris inside the flue.
What it costs in Haltom City
Liner replacement in Haltom City runs $2,500-$5,500 depending on flue length and existing conditions.
How we do it
We remove or bypass the damaged clay liner, then install a correctly sized stainless steel system with a documented photo record before and after.
Partial Rebuild
Signs you need it
The section above the roofline is leaning, cracked, or shedding bricks, but the lower chimney is still structurally sound.
What it costs in Haltom City
A partial rebuild in Haltom City runs $2,500-$6,000 depending on how many courses of brick must come down.
How we do it
We take the chimney down to sound masonry, relaid the removed courses with proper joints, and install a new crown and cap.
What Chimney Liner & Rebuild Costs in Haltom City
| Item | Typical range in Haltom City |
|---|---|
| Stainless steel liner | $2,500-$5,500 |
| Flexible liner | $2,500-$5,000 |
| Partial rebuild | $2,500-$6,000 |
Do I really need a new liner, or is that an upsell?
The camera footage decides. If the liner is cracked, separated, or undersized, the risk of heat transfer to the house structure is real. You see every frame before we recommend anything. Call (980) 580-8641 for a second opinion.
How long does a liner replacement take in Haltom City?
Most liner replacements finish in one day. A partial rebuild runs two to three days depending on weather and material availability. Call (980) 580-8641 for a written timeline.
Brands We Service in Haltom City
We stock and install components from DuraFlex, Copperfield, and Famco, which covers most liner, cap, and crown jobs in Haltom City without a special-order wait. Parts are sourced through our buying network to keep the pricing honest, and common sizes are on the truck. See our brands for the full list and spec sheets.
Pricing for Chimney Cleaning in Haltom City, TX
| Service | Typical range in Haltom City |
|---|---|
| Level 1 Inspection | $99-$180 |
| Level 2 Inspection with camera scan | $199-$350 |
| Standard sweep with inspection | $169-$289 |
| Creosote removal | $149-$300 |
| Soot removal | $129-$199 |
| Mortar repointing | $35-$55 per square foot |
| Spalling brick repair | $700-$2,500 |
| Chimney waterproofing | $250-$600 |
| Flashing repair | $450-$1,400 |
| Stainless steel liner | $2,500-$5,500 |
| Flexible liner | $2,500-$5,000 |
| Partial rebuild | $2,500-$6,000 |
Two things push prices up in Haltom City: the age of the chimney and what the camera reveals once we’re inside. A 60-year-old flue with hidden joint separation costs more to make safe than a clean 1990s chimney, and we’d rather show you that on video than surprise you with a change order. Every quote is written, itemized, and delivered before any work starts.
Neighborhoods We Serve in Haltom City
We work throughout Haltom City, from the older ranch-home blocks near the original city core to the streets that border North Richland Hills and Fort Worth. Most neighborhoods fall within a 15-minute drive of our local dispatch point, so scheduling a sweep the week you call is usually straightforward.
- Original Haltom City core near Broadway and Denton Highway
- North Haltom City along NE 28th Street
- Haltom City neighborhoods bordering Fort Worth’s Diamond Hill area
- East Haltom City near Watauga and the Richland Hills line
- Haltom City neighborhoods off Midway Road and Beach Street
Service Area - Cities Near Haltom City
Beyond Haltom City, we cover Fort Worth, TX, North Richland Hills, TX, and Hurst, TX with the same camera-scan standard. For our New England operations, see Bedford, NH. Scheduling is coordinated from the brand’s Dallas-Fort Worth office, and crews serve Haltom City locally.
Serving Haltom City, TX - Our Local Coverage Area
We’re based in the Haltom City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Haltom City
Most sweeps and inspections in Haltom City can be scheduled the same week you call. We send a text when the named technician is on the way, and jobs are quoted in writing before any work begins. Call (980) 580-8641 to check this week’s openings.
A routine sweep and inspection requires no permit anywhere in Tarrant County. Structural work like a full chimney rebuild or certain liner installations may, and we confirm requirement status for your specific address before the job is scoped. Call (980) 580-8641 with your property details.
Every visit ends with a photo record of the flue interior, the firebox, and the exterior crown, plus a written scope and warranty. Clause 4 of the Haven Standard requires the photo record on every job, and we’ve kept that archive running since 2009. Call (980) 580-8641 to schedule yours.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Haltom City Customers Say
"They told me the flue was fine and I did not need a liner. Charged me for the inspection and nothing else. That is why I have called them twice since."
- Hal M."Cap and crown replaced after water was getting in. Price was quoted in writing, and they showed me the mortar failure first."
- Neil O."Gas insert service done properly with the readings written down. The technician had the certification number printed on the paperwork."
- Bettina A.