Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterFast, Reliable Chimney Cap & Crown Across Bloomington
Chimney cap and crown work in Bloomington typically runs $220 to $640 for caps and $380 to $1,150 for crown repair or coating, and most jobs are completed in one visit. We dispatch crews from our Inland Empire office directly into Bloomington’s neighborhoods, usually within a few days of the first call. If you have a cracked crown, a missing cap, or debris falling into a flue that has sat cold through No-Burn season, we will show you camera footage of the actual problem before quoting anything. Call (980) 580-8641 and we will get a technician to your Bloomington property fast.
Why Emberly Chimney Cleaners Is Bloomington’s Preferred Chimney Cap & Crown Company
Climate shapes the work here more than any other factor. The San Bernardino Valley’s hot summers and hard freezes crack mortar joints and flue tiles faster than most homeowners realize, and what starts as a small crown crack is, within a season or two, a water path into the firebox. Our Chimney Cap & Crown team works under the Haven Standard, which means every job begins with a written price and ends with a documented photo record of what we did. Clause 4 has been part of our process since 2009, and since then we have inspected and cleaned more than 38,000 chimneys. No recommendation is delivered verbally and left to your imagination. Corrine Halstead, who leads our team, has built the entire operating model around evidence you can see.
Bloomington homeowners tell us the same thing across dozens of jobs in the Bloomington Farms tract, Mission Bell, and the neighborhoods along Cedar and Slover Avenues: they want an inspection that shows them exactly what is wrong before money moves. We do that. Every visit includes a camera scan, and nothing is recommended without footage you watch yourself.
Our Chimney Cap & Crown Services in Bloomington
Cap Installation
Most Bloomington homes we service have either no cap or a rusted cap with mesh that has torn away. That is an open invitation for starlings and roof rats during the months curtailment days keep your flue idle. We install stainless caps sized to your flue, including multi-flue options for homes with two flues side by side. A new cap on a Bloomington ranch costs $220 to $480 installed in most cases.
Cap Replacement
When the cap is old enough that the spark arrestor is gone or the frame is corroded through, replacement is usually cheaper than fiddling with patchwork. We match the cap to the flue dimensions and the chimney’s exposure to Santa Ana wind. If your cap howls on windy nights near the Bloomington Airport, a replacement with the right mesh gap usually stops it.
Crown Repair
Spalling crowns are the most common finding on 1950s through 1970s tract homes in Bloomington. The Inland Empire’s thermal swings mean a crown poured too thin, or one that was never sealed, will eventually crumble at the edges. We remove loose material, rebuild the crown with proper slope and a drip edge, and seal it. Typical crown repair in Bloomington runs $650 to $950 for a full rebuild, less when the damage is confined to one section.
Crown Coating
When the crown is intact but porous, a coating is the right fix. We use Gelco sealant applied to the cleaned crown surface, which rejects water and flexes enough to survive freeze-thaw cycles. This matters on older Bloomington fireplaces where the crown was cast with no expansion joint. Coating runs $380 to $520 for a standard single-flue chimney.
Every one of these services is quoted in writing before work begins. No exceptions. That is Haven Standard Clause 1, and it is how we have done business since 2009.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Bloomington
We stock materials from Famco, Copperfield, and Olympia Chimney specifically because they hold up in the Inland Empire’s weather. Bloomington customers are not waiting weeks on a part order. We keep common cap sizes and crown sealants on our trucks and in our local inventory because we know that when a crown is spalling, waiting a month means more water in the firebox. Whether your home has a masonry chimney or a factory-built metal chimney on a manufactured home, we have the right cap and the right coating without a special-order delay.
Common Chimney Cap & Crown Problems We See in Bloomington Homes
- Spalling crowns from thermal cycling. Bloomington summers push past 105°F and winter nights can drop below freezing, and that repeated expansion and contraction shatters thin mortar crowns. The failure starts at the outer edge and works inward, exposing the flue to direct rain.
- Animal nesting in dormancy windows. SCAQMD No-Burn days can sit heavy in the basin for weeks, and flues that stay cold for months collect barn owl pellets, starling nests, and roof rat debris. A cap with torn mesh or no cap at all turns those months into a wildlife problem inside the chimney.
- Santa Ana wind debris and draft reversal. Strong winds drive leaves and ash into uncapped flues and push smoke back into the home when a cap’s spark arrestor is clogged or missing. Mobile home metal chimneys on Bloomington lots are especially exposed.
- Water intrusion through cracked crowns on rental properties. Bloomington has a meaningful share of long-vacant or low-income rentals where crowns have failed and nobody noticed until a tenant reports water in the firebox. By then the damage is well past a coating.
Pricing for Chimney Cap & Crown in Bloomington, CA
Here is what we quote across Bloomington on a regular basis. A standard single-flue stainless cap install runs $220 to $380. A multi-flue cap on a two-flue chimney runs $380 to $480. Custom caps, which we handle for oversized or oddly shaped flues on older custom homes in the area, start around $550 and go up based on the pattern. Crown coating sits at $380 to $520. Full crown rebuilds run $650 to $950, and the higher end usually means we are also regrinding the flue wash and adding a drip edge. Every job includes the camera scan and the written photo report afterward, whether you book a $220 cap or a $1,000 rebuild. Free estimates are standard. Call (980) 580-8641 for a written number on your specific chimney.
We Also Serve Cities Near Bloomington
When we are not working in Bloomington, we are running cap and crown jobs in Rialto, Fontana, Riverside, and Colton. If you are in one of those areas, the same camera-scan standard and written pricing apply. Bloomington customers get the same crew, the same Haven Standard documentation, and the same 365-Day Done Right Promise as every job we run in the Bloomington area. The promise is stamped on every job, and it is simple: if it is not done right, we make it right.
Serving Bloomington, CA - Our Local Coverage Area
We’re based in the Bloomington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Chimney Cap & Crown in Bloomington
Because the chimney is still exposed to weather and wildlife year-round. Bloomington’s No-Burn curtailment days under SCAQMD keep flues cold for long stretches, and that is exactly when starlings, barn owls, and roof rats move in through a missing or damaged cap. A cracked crown also keeps deteriorating whether you burn or not, because the thermal cycling of the Inland Empire does not pause during curtailment. A chimney that sits unused still needs a functioning cap and a sealed crown. Call (980) 580-8641 for a camera inspection and a written price.
Look for crumbling mortar at the crown’s outer edges, small stone or sand-like particles washing into the gutter after rain, and a white chalky residue on the brick near the top. Spalling in Bloomington tends to show up first on the sun-baked south and west faces of the chimney, where direct afternoon heat hits hardest. If the crown surface looks sandy or pitted, water is already getting in. We can confirm it with camera footage of the flue interior.
Yes. Factory-built metal chimneys use a different flue diameter and a cap that locks onto the pipe rather than one that spans a masonry crown. Installing a masonry-style cap on a metal chimney can damage the pipe and create a fire hazard. Our techs carry caps matched to manufactured home systems, including components sourced from Olympia Chimney and Famco, so the install is specific to the appliance’s factory specs.
A properly fitted stainless cap with intact mesh will keep roof rats out of the flue, which is the most common entry point we see on older Bloomington rentals that have sat vacant during curtailment months. What a cap cannot do is fix soffit gaps, roof vents, or wall penetrations. When we pull a nest out of a flue, we show you the photo and tell you plainly whether the cap was the problem or whether something else is also letting them in. For a rent-ready camera scan and quote, call (980) 580-8641.
A coating is a waterproof sealant applied to a crown that is still structurally sound but porous; a full repair removes the damaged material and rebuilds the crown. Most 1960s Bloomington fireplaces fall into the repair category by the time we see them, because the original crown was cast too thin and 60 years of Inland Empire heat has spalled the edges away. If the crown is cracking and losing chunks, coating over it will not stop the water. We will show you the camera view that confirms which branch of work your chimney actually needs before we quote either one.
Get a Written Quote for Chimney Cap & Crown Work in Bloomington
If your Bloomington chimney needs a cap, a crown repair, or a straight answer about what the camera shows, call (980) 580-8641. We answer 24/7, even on SCAQMD burn days when the phone rings off the hook. Every visit starts with a camera scan, ends with a written photo record, and includes a written price before any work begins. No upsell, no guesswork. Just proof you can see. Corrine Halstead built this team around that principle, and it is how we have done 38,000-plus inspections since 2009.
Written by Corrine Halstead, Owner at Emberly Chimney Cleaners, coordinating Chimney Cap & Crown in Bloomington under the Haven Standard since 2009.