Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterChimney Cleaning in Revere, MA
Chimney cleaning in Revere, MA typically costs $139-$329 for a standard sweep with a Level 1 inspection, and we recommend it annually for any wood-burning fireplace in this city. Revere’s early-20th-century two- and three-family homes sit blocks from the open Atlantic, which means salt-air corrosion hits chimneys faster here than almost anywhere else in the Boston metro. Call (980) 580-8641 for a written price before any work begins.
Why Revere Homes Are Different
Revere’s housing stock creates chimney problems that a standard cleaning alone won’t catch. Most homes east of Broadway were built between 1910 and 1950, and their chimneys were sized for oil boilers. When those boilers got converted to gas, the flues suddenly ran cooler, which lets acidic condensate eat at the clay liners from the inside. Wood-burning fireplaces in the same chase then glaze with creosote faster because the overall flue temperature stays lower.
On top of that, Revere Beach offers zero protection from nor’easters. Wind-driven rain slams into crowns and mortar joints all winter, and the salt air corrodes galvanized flashing and caps at a rate you won’t see inland. Technicians working east of Revere Beach Boulevard regularly find standard galvanized caps rusted through in five years or less. A chimney cleaning in Revere should always include a salt-damage assessment. We do that on every job here, because skipping it would be negligent given what the ocean does to masonry.
Our Main Revere Services
These two services come up constantly in Revere because of the salt and the aging flues. If you need one of them, start here.
Fireplace Services in Revere
Revere homes with original fireplaces often have fireboxes that are structurally sound but glazed with decades of creosote. Others have dampers rusted shut from years of salt air creeping down the flue. Our fireplace service starts with a camera inspection of the firebox, damper, and smoke chamber, then a written scope of what actually needs work. Some fireplaces just need a thorough cleaning and a new gasket. Others need refractory panel replacement or a damper rebuild. You’ll see photos of every problem before you approve a dollar. Fireplace Services in Revere
Chimney Cap & Crown in Revere
The crown is the concrete slab at the top of your chimney, and in Revere it takes a beating. Wind-driven rain from the Atlantic soaks the crown, freezes in January, and spalls the surface. Once the crown cracks, water gets behind the brick and accelerates everything else. Caps are equally vulnerable here. Salt air destroys galvanized caps within five years on ocean-facing blocks, so we recommend stainless steel for almost every Revere install. Chimney Cap & Crown in Revere
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterChimney Cleaning & Sweep in Revere
Chimney cleaning and sweeping in Revere costs $139-$329 depending on creosote buildup and flue condition, and the salt air here makes an annual camera check more important than it is inland. Every Revere sweep we do includes a Level 1 inspection as the baseline, and we recommend a Level 2 camera inspection on any chimney that hasn’t been documented in the past three years, especially in pre-1950 multi-family buildings with original clay liners. Our full Chimney Cleaning & Sweep service includes a written photo record on every visit, consistent with Clause 4 of the Haven Standard.
Level 1 Inspection
Signs you need it
You use your fireplace regularly and want confirmation that the flue is clear and the chimney is safe to burn.
What it costs in Revere
A Level 1 inspection is included with any chimney cleaning we do, which runs $139-$329 in Revere depending on flue condition.
How we do it
We check the readily accessible portions of the chimney, flue, and appliance connections, then document findings with photos.
Creosote Removal
Signs you need it
You see shiny black tar-like buildup on the flue walls, or your fires have been burning cooler and smokier than they should.
What it costs in Revere
Creosote removal in Revere typically adds $25-$50 to the standard sweep when there’s heavy glazing that requires extra mechanical brushing.
How we do it
We use rotary brushes and hand scrapers to remove glazed creosote, then re-inspect with a camera to confirm the flue is clean.
Level 2 Inspection
Signs you need it
You’ve had a chimney fire, bought a new home, or changed heating appliances, and need a documented camera scan of the full flue.
What it costs in Revere
A Level 2 camera inspection runs $200-$350 in Revere and is often combined with the cleaning for one visit fee.
How we do it
We run a video camera down the full length of the flue, checking for cracks, gaps, and hidden creosote, then give you the footage.
What Chimney Cleaning & Sweep Costs in Revere
| Item | Typical range in Revere |
|---|---|
| Standard chimney sweep with Level 1 inspection | $139-$329 |
| Level 2 camera inspection | $200-$350 |
| Creosote removal add-on | $25-$50 |
How often should a chimney be cleaned in Revere?
Annually if you burn wood more than a dozen times a season. Salt air accelerates mortar deterioration, so even light users should get a camera check every two years to catch early spalling before it becomes a liner replacement.
Do I really need a camera inspection every year?
Not every year, but every three years at minimum. Revere’s ocean-facing exposure means hidden flue damage develops faster than inland, and the camera is the only way to document what’s actually happening inside the clay liner. Call (980) 580-8641 for a written quote.
Chimney Repair in Revere
Chimney repair in Revere costs $200-$2,600 depending on whether we’re repointing mortar joints or rebuilding a spalled crown, and salt air makes this city a high-wear zone for masonry. The two- and three-deckers built in the 1920s and 1930s often have original brick that’s been soaking up Atlantic moisture for a century. Our Chimney Repair work starts with a camera scan and a written scope, so you know exactly what’s failing before any tool comes off the truck.
Mortar Repointing
Signs you need it
You see crumbling or missing mortar between bricks, or sandy grit collecting at the base of the chimney.
What it costs in Revere
Repointing in Revere runs $200-$600 for typical spot work, or $40-$100 per linear foot for full joint replacement.
How we do it
We grind out deteriorated mortar, pack in fresh weather-resistant mix, and tool the joints to match the original profile.
Flashing Repair
Signs you need it
You see water staining on ceiling joists near the chimney, or the metal flashing at the roofline is rusted through or pulling away.
What it costs in Revere
Flashing repair in Revere typically costs $300-$850 depending on how much of the flashing needs replacement.
How we do it
We remove the corroded flashing, install new metal with proper counter-flashing, and seal all joints against wind-driven rain.
What Chimney Repair Costs in Revere
| Item | Typical range in Revere |
|---|---|
| Mortar repointing | $200-$600 |
| Flashing repair | $300-$850 |
| Chimney crown repair | $600-$1,400 |
Can you fix a leaning chimney in Revere?
A leaning chimney usually means the foundation or the upper masonry has shifted, which is a structural repair, not a cosmetic one. We’ll assess it with a camera and a level, then give you a written scope and price. Call (980) 580-8641.
Is it safe to burn with cracked mortar joints?
Not for long. Cracked joints let water in, and water plus freeze-thaw cycles in Revere winters widens those cracks fast. It also lets heat reach combustible framing. Get it inspected before the next burn season. Call (980) 580-8641.
Chimney Liner & Rebuild in Revere
Chimney liner and rebuild work in Revere costs $2,500-$8,500 for a full liner replacement or partial rebuild, and the oil-to-gas conversions in this city make liner failure one of the most common findings we document. Clay liners sized for oil boilers run too cool on gas, which creates acidic condensate that eats the mortar between the tiles. Our Chimney Liner & Rebuild team installs stainless steel liners sized correctly for the new appliance, using DuraFlex and HeatShield materials.
Stainless Steel Liner
Signs you need it
Your gas boiler or furnace exhausts into an old clay-lined flue that’s spalling or missing mortar joints, or you see condensation staining at the base.
What it costs in Revere
A stainless steel liner in Revere runs $2,500-$5,500 installed, depending on flue height and access.
How we do it
We size the liner to the appliance, drop it down the flue, insulate as needed, and document the full install with a camera scan.
Partial Rebuild
Signs you need it
The top few feet of your chimney are spalled, cracked, or missing bricks, but the lower section is still sound.
What it costs in Revere
A partial chimney rebuild in Revere typically runs $4,000-$8,500 depending on how many courses need replacing.
How we do it
We tear down to solid masonry, rebuild with new brick and a proper crown, and flash everything to shed water.
What Chimney Liner & Rebuild Costs in Revere
| Item | Typical range in Revere |
|---|---|
| Stainless steel liner install | $2,500-$5,500 |
| Partial chimney rebuild | $4,000-$8,500 |
| Full chimney rebuild | $8,000-$15,000 |
Do I really need a new liner, or is the old one fine?
You’ll see the answer on camera. If the clay tiles are cracked, missing, or the mortar joints are gone, the liner is no longer doing its job and needs replacement. You don’t have to take our word for it. Call (980) 580-8641 for a written estimate.
What happens if I skip a liner replacement?
Heat and gases leak through the cracks into the chimney chase, which is a fire risk and a carbon monoxide risk. On gas appliances, acidic condensate keeps eating the masonry until the chimney is no longer safe to vent. Call (980) 580-8641.
Brands We Service in Revere
We work on chimneys built with every major brand, and we stock parts locally for Famco, Copperfield, and DuraFlex installs. If a part is in stock, most Revere repairs can be completed in a single visit. See our brands for the full list.
Pricing for Chimney Cleaning in Revere, MA
| Service | Typical range in Revere |
|---|---|
| Standard chimney sweep with Level 1 inspection | $139-$329 |
| Level 2 camera inspection | $200-$350 |
| Creosote removal add-on | $25-$50 |
| Soot removal | $100-$200 |
| Mortar repointing | $200-$600 |
| Flashing repair | $300-$850 |
| Chimney crown repair | $600-$1,400 |
| Stainless steel liner install | $2,500-$5,500 |
| Partial chimney rebuild | $4,000-$8,500 |
| Full chimney rebuild | $8,000-$15,000 |
Prices in Revere run higher than inland suburbs because of what the salt air does to flashing, caps, and mortar joints. Ocean-facing homes on blocks east of Revere Beach Boulevard routinely need stainless steel parts instead of galvanized, which adds to material cost. Every job gets a written price before work starts. That’s Clause 1 of the Haven Standard, and we don’t work any other way.
Neighborhoods We Serve in Revere
We work throughout Revere, from the three-deckers near Shirley Avenue to the single-family streets off Winthrop Parkway. Typical response time for a cleaning or inspection is 2-4 business days, and we schedule around nor’easter season when scaffolding work gets delayed by wind.
- Beachmont
- Oak Island
- Point of Pines
- West Revere
- Downtown Revere
Service Area - Cities Near Revere
We also serve Chelsea, MA, Everett, MA, Malden, MA, and Saugus, MA. Each of those cities has its own housing stock and chimney profile, but the same salt-air issues on ocean-facing blocks appear in Chelsea and parts of Everett. If you’re nearby and need a camera inspection or a written quote, we can help.
Serving Revere, MA - Our Local Coverage Area
We’re based in the Revere area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Revere
We typically schedule Revere visits within 2-4 business days. Nor’easter season can push exterior work back when wind makes scaffolding unsafe, but interior cleaning and camera inspections happen year-round.
Most routine chimney cleaning and inspection work doesn’t require a permit. Structural rebuilds or liner installations may, depending on scope. We’ll tell you during the written quote phase if a permit applies to your job.
It does. Galvanized steel caps that last 20 years inland corrode through in five years on ocean-facing Revere blocks. The salt also attacks mortar joints and flashing. We adjust every Revere quote to account for that exposure, which is why stainless steel is our default recommendation here.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Revere Customers Say
"Found a bird nest and a blocked flue we had no idea about. Photographed everything, cleared it, and explained what the smell had been."
- Curtis V."They told me the flue was fine and I did not need a liner. Charged me for the inspection and nothing else. That is why I have called them twice since."
- Hal M."Cap and crown replaced after water was getting in. Price was quoted in writing, and they showed me the mortar failure first."
- Neil O.