Chimney Cap & Crown in Easton - Measured On Site, One Written Price

Fast, Reliable Chimney Cap & Crown Across Easton

A chimney cap and crown in Easton typically runs $280-$1,650 depending on whether you need a standard single-flue cap, a custom multi-flue cap, or a full crown rebuild. Most cap replacements are done in a single visit; crown repair or rebuild usually takes one day on site, with the new mortar curing over the following week. If water is getting into your chimney or you’re seeing spalling brick faces on an Easton row home, call (980) 580-8641 and we’ll schedule a camera inspection with a written price before any work starts.

Easton’s housing stock is genuinely different from the rest of the Lehigh Valley. We work these blocks every week, from College Hill to the West Ward, and we know what a century-old lime-mortar chimney looks like on the inside. Your chimney was probably built for coal. What it’s venting now is a different job entirely.

Why Emberly Chimney Cleaners Is Easton’s Preferred Chimney Cap & Crown Company

We carry a camera down every flue before recommending anything. That’s not a pitch; it’s Clause 4 of the Haven Standard, the inspection standard we’ve worked to since 2009. On Easton’s pre-1900 chimneys, a visual check from the ground or roof tells you almost nothing. The flue runs inside a brick stack you can’t see through. So we show you the footage. If the crown is cracked and water is tracking into lime mortar, you’ll see it on the screen. If the flue tiles are intact and the cap just needs replacement, you’ll see that too, and we’ll tell you plainly that the liner can wait.

Corrine Halstead leads our crews, and every tech who shows up at an Easton door is background-checked, uniformed, and assigned by name. You get a text when they’re on the way. You get a written scope, written price, and written warranty before anyone picks up a trowel. That’s Clause 1 of the Haven Standard: have it in writing. It’s been that way on all 38,000-plus inspections and cleanings we’ve completed since 2009.

Our Chimney Cap & Crown Services in Easton

Cap Installation

A correctly sized stainless steel cap keeps rain, animals, and debris out of an active flue. In Easton’s older homes, we’re often installing caps on flues that never had one. That’s normal for a coal-era chimney. We measure the flue tile, not the brick opening, so the cap actually fits and drafts correctly. Standard single-flue cap installation in Easton runs $280-$420, including the cap, fastening, and a photo record of the completed work.

Cap Replacement

If your existing cap is rusted through, dented by falling branches, or simply the wrong size for the flue, replacement is straightforward and usually done in one visit. We see a lot of galvanized caps on older Easton homes that have corroded after ten or fifteen years of Delaware River humidity. We replace them with stainless steel from Olympia Chimney or Famco. Replacement runs $300-$520 in Easton, and we haul the old cap away.

Crown Repair

The crown is the concrete or mortar slab that seals the top of the chimney around the flue. On Easton’s pre-1900 stacks, most crowns were built with the same lime mortar used for the brick, and that material was never meant to shed water for a century. When freeze-thaw cycles crack it, water gets into the chimney’s core and pushes brick faces off over time. Crown repair, including patching cracks and restoring slope, runs $450-$850. Full crown rebuild starts around $950 and goes up based on access and the number of flues.

Crown Coating

For crowns that are structurally sound but showing hairline cracking, we apply a flexible crown coating, typically a product from Gelco, that bridges small cracks and keeps water out for years. Coating is the most cost-effective intervention when caught early. In Easton, crown coating runs $350-$550. It’s not a substitute for a proper rebuild if the crown has already separated from the flue, and we’ll tell you the difference on camera before quoting either.

Before

After

Trusted Brands We Service in Easton

We stock and install caps from Olympia Chimney and Famco, and we use Gelco crown coating products. For Chimney Cap & Crown work that requires flue access or liner interface, we also work with Copperfield components. When a replacement part is ordered for an Easton job, it arrives at our shop before the crew is scheduled. We don’t start a job waiting on parts, and we don’t sell you a brand we wouldn’t put on our own chimney.

Common Chimney Cap & Crown Problems We See in Easton Homes

• Spalling brick faces below the crown. Water enters through a cracked crown, soaks the top courses of brick, then freezes and expands. The brick face pops off. On Easton’s lime-mortar chimneys, this happens faster than in newer suburban construction because the mortar holds more water and the river humidity slows drying.
• Cross-draft in multi-flue stacks. A single aging masonry stack in the West Ward often vents a furnace, fireplace, and water heater with no dividing tile liner. Without properly spaced caps on each flue, exhaust from one flue gets pulled into another. That’s how carbon monoxide ends up in a basement.
• Animals nesting in dormant flues. If one flue in a multi-flue stack isn’t being used, and it has no cap, squirrels and birds move in fast. When that appliance cycles back on in the fall, the nest blocks the draft and pushes exhaust into the house.
• Rusted or missing caps on gas-converted chimneys. Many Easton row homes were converted from coal to gas decades ago. The flue that once vented a coal fire now vents a gas furnace, and if the old cap is rusted through or gone, rain runs straight down the flue and into the appliance.

Pricing for Chimney Cap & Crown in Easton, PA

We Also Serve Cities Near Easton

Our crews work Chimney Cap & Crown in Easton every week, and we regularly travel to Bethlehem, Allentown, Pottstown, and Levittown for cap, crown, and full service work. The same camera-scan standard, written pricing, and photo record apply on every job. If you’re a few miles outside Easton, scheduling is coordinated from our Philadelphia office, and crews serve the surrounding area locally.

FAQs - Chimney Cap & Crown in Easton

How do I know if my Easton chimney crown needs repair or full replacement?

You need a camera inspection, not a guess. A crown with hairline cracks and a stable base can often be repaired or coated. A crown that has separated from the flue, crumbled at the edges, or let water soak the top courses of brick usually needs a full rebuild. On Easton’s older chimneys, we photograph everything from the roof and the flue interior, then give you a written recommendation with the footage to back it up. Call (980) 580-8641 for an inspection and quote.

My West Ward row home has three flues in one chimney. Can one cap cover them all?

Yes, with the right cap. A multi-flue cap spans the entire chimney top and covers all three flues while allowing each to draft separately. But it has to be sized and spaced correctly, or exhaust from one flue pulls into the next one. That cross-draft is exactly what we found on a tightly packed block in the West Ward: a three-flue chimney with a deteriorating crown and no caps, venting a gas furnace and water heater through unlined 19th-century brick. We rebuilt the crown with proper slope, installed a custom multi-flue cap with correct spacing, and the backdraft stopped. Camera evidence showed the fix worked.

Why does my Easton chimney cap keep rusting or blowing off after a few years?

Rust is usually a materials problem. Galvanized steel caps fail faster in Easton’s river humidity than stainless steel does. We install stainless caps from Olympia Chimney or Famco for this reason. Blowing off is a fit problem. If the cap sits on the brick instead of inside the flue tile, wind gets under it. The fix is a cap sized to the flue and mechanically fastened, not slid over the outside. We see both failures regularly on Easton row homes.

Can I install a chimney cap myself on my historic Easton row home?

We’d recommend against it, for two reasons. First, you’re working at roof height on a structure that predates modern fall protection. Second, a badly fitted cap on an old multi-flue stack can create the cross-draft problem described above, and you won’t know it’s happening until a carbon monoxide detector goes off. This is one of those jobs where the stakes justify a trained professional.

Do I need a cap on a chimney that only vents a gas furnace?

Yes. An uncapped flue lets rain run directly down into the appliance, corrodes the interior, and invites animals to nest when the furnace cycles off in warm months. In Easton, we regularly find uncapped gas flues where water has been pooling at the burner level for years. Call (980) 580-8641 and we’ll inspect, cap, and document the whole thing.

Get a Written Quote for Chimney Cap & Crown Work in Easton

If you own an older Easton home, your chimney deserves an honest camera look before anyone sells you a rebuild. That’s what we do. Call (980) 580-8641 to schedule an inspection with a written quote, a named tech, and a photo record included. Or bring us a competitor’s written estimate and we’ll give you a free second opinion. Every job is backed by the 365-Day Done Right Promise: if it’s not done right, we make it right.

Written by Corrine Halstead, Owner at Emberly Chimney Cleaners, serving Easton under the Haven Standard.