Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Cleaning in Camas, WA
Chimney cleaning in Camas, WA costs between $189 and $319 for a standard sweep with a Level 1 inspection, and most homeowners in the area need it done every one to two years. Homes here face a specific mix of problems: older Craftsman chimneys near downtown carry decades of creosote on original clay liners, while the hillside subdivisions built in the 2000s have prefabricated fireplaces now hitting the age where rust and chase-cover failures quietly become structural issues. If you’re seeing soot streaks, smelling smoke in the house, or you’ve never had the flue camera-scanned, call (980) 580-8641 for a written quote before any work starts.
Why Camas Homes Are Different
Camas sits at the western mouth of the Columbia River Gorge, where easterly winds gusting to 40 mph create draft conditions unlike anything else in Clark County. Those intermittent easterlies push smoke back down chimneys and cause uneven burn cycles, which accelerates the condensation of creosote on flue walls. Then the long wet season from October through April means fireplaces run for months in cold, damp air, adding sticky, moisture-heavy creosote that hardens into the most stubborn kind to remove. On Prune Hill and similar hillside subdivisions from the 2000s boom, we regularly find fireplaces that have never been cleaned once since the home was built. Many of those prefabricated units are now 15 to 25 years old and approaching the end of their rated service life. Owners treat them as maintenance-free, and they are not.
Our Main Camas Services
Two services dominate the calls we take from Camas homeowners. Both are tied directly to the local housing mix and the Gorge weather, and both are quoted in writing before any work begins.
Fireplace Services in Camas
Factory-built fireplaces in the Prune Hill corridor often fail in ways a cleaning alone cannot fix: rusted chase covers, water-damaged framing, gas logs that no longer seat properly, and refractory panels cracked from years of uneven heating. A quick look at the firebox is not enough to know what is going on. Fireplace Services in Camas covers everything from gas log replacement to full unit repair, and the job always starts with a camera scan and a written scope.

Chimney Cap & Crown in Camas
The Gorge winds and persistent rain work hard on chimney caps and concrete crowns in Camas. A cracked crown lets water seep into the masonry, and freeze-thaw cycles through the wet season widen those cracks every year. Once water gets behind the brick, the real damage starts. Chimney Cap & Crown in Camas includes full inspection of the crown, cap, and chase cover, with photos of every finding before you approve any repair.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterChimney Cleaning & Sweep in Camas

Chimney cleaning in Camas is not a one-size job. The older Craftsmans and mill-era homes near downtown often have original clay liners carrying decades of creosote that cannot be safely removed with a simple brush-and-vacuum pass. Meanwhile, the newer prefabricated units on Prune Hill collect a dense, moisture-logged creosote from the damp Gorge air that bakes into something closer to tar than soot. You need a sweep who knows which chimney is which, and what each one needs as it ages. Our standard practice follows Level 2 protocol on every first visit: a camera down the flue before and after, documented in a photo report you keep. Find more about the standard we work to on the Chimney Cleaning & Sweep page.
Creosote Removal
Signs you need it
The strongest sign is a smell like asphalt or campfire smoke indoors even when the fireplace has been cold for days, which means hardened deposits are off-gassing down the flue.
What it costs in Camas
Creosote removal in Camas typically costs $220 to $380 depending on the class of buildup, with heavy tar-glazed deposits toward the top of that range.
How we do it
We identify the creosote class on camera first, then apply the right mechanical tools or chemical treatment for that class, never the same approach for every flue.
Level 2 Inspection
Signs you need it
If you bought your Camas home and the previous owner left no record of chimney service, a Level 2 inspection is what the NFPA 211 standard says the new owner should get before lighting the first fire.
What it costs in Camas
A Level 2 camera inspection in Camas runs $250 to $400 when booked as a standalone visit, and we include a written photo report with every one.
How we do it
We run a video camera the full length of the flue from firebox to cap, document liner condition, clearances, and any obstruction, and give you the footage before leaving.
Soot Removal
Signs you need it
Fine black dust settling on furniture near the hearth, or visible soot streaks at the firebox opening, means the chimney is not drafting correctly for the fuel load.
What it costs in Camas
Soot removal in Camas typically runs $189 to $250 as part of a standard sweep, and it is almost always paired with creosote removal when the flue has not been serviced in years.
How we do it
We brush the full flue length, HEPA-vacuum the firebox and smoke chamber, and check the damper and chimney cap for blockages in the same pass.
Annual Sweep
Signs you need it
If your last sweep in Camas was over a year ago and you burn more than a cord of wood per season, schedule the next one before October, not after the first fire.
What it costs in Camas
An annual sweep with a Level 1 inspection in Camas costs $189 to $319 depending on flue length, and we write that price before we arrive.
How we do it
We sweep the full flue, remove all debris, run the Level 1 check on accessible components, and leave you with a photo record of the flue before and after the sweep.
What Chimney Cleaning & Sweep Costs in Camas
| Item | Typical range in Camas |
|---|---|
| Standard sweep with Level 1 inspection | $189 - $319 |
| Creosote removal (dependent on class) | $220 - $380 |
| Level 2 camera inspection (standalone) | $250 - $400 |
How often should a Camas chimney be cleaned?
Every one to two years, depending on burn frequency and creosote class. Camas’s damp, low-cloud marine air produces heavier, stickier creosote than drier inland climates, so annual inspection is the safer default. Call (980) 580-8641 and we’ll quote your sweep in writing.
Can you clean a prefab fireplace in Camas the same way as a masonry one?
No, and confusing the two causes real damage. Prefab units need specific brushes and care around the factory collar and chase. We identify the unit type before any tool touches the flue. Call (980) 580-8641 for a written quote.
Chimney Repair in Camas

Chimney repair in Camas usually starts with one of two discoveries: cracked and failing mortar on a downtown masonry chimney, or water intrusion behind a hillside prefab unit’s rusted chase cover. The Gorge winds push rain against the west and south faces of chimneys, and those wet, wind-blasted sections deteriorate faster than any other side of the house. Repairs range from simple repointing to partial rebuilding, and the right fix depends on what the camera and moisture readings actually show. See the full scope of what falls under Chimney Repair and how we price it before starting.
Mortar Repointing
Signs you need it
If you can scrape mortar out of the joints with a house key, the chimney masonry is failing and water is getting in every time it rains.
What it costs in Camas
Mortar repointing on a typical Camas chimney runs $800 to $2,500 for partial repointing, with the price driven by access and how many courses need work.
How we do it
We grind out compromised joints, pack in fresh mortar matched for compression strength to the existing brick, and waterproof the section when the job allows it.
Flashing Repair
Signs you need it
A water stain on the ceiling near the chimney, or damp spots in the attic around the chimney chase, point to failed flashing rather than a roof leak.
What it costs in Camas
Flashing repair in Camas typically runs $400 to $1,400, and the range widens when the old flashing was installed with roofing cement instead of a proper step-flashing design.
How we do it
We remove the failed material, inspect the wood beneath, install step and counter-flashing cut to fit, and photo-document the new laps before closing up.
What Chimney Repair Costs in Camas
| Item | Typical range in Camas |
|---|---|
| Mortar repointing (partial) | $800 - $2,500 |
| Flashing repair | $400 - $1,400 |
| Chimney waterproofing | $600 - $1,800 |
Can a rusted chase cover on a Prune Hill prefab be repaired, or does it need replacement?
Most rusted chase covers need replacement. Once the metal has thinned and pitted, patching buys less than a season in Camas’s wet climate. A replacement is the only option we’ll put in writing. Call (980) 580-8641 for a free estimate.
How do I know if my Camas chimney needs repair before it becomes expensive?
The camera scan shows it. Hairline cracks in the liner, spalling brick faces, and rust-lifted flashing all show up on video before they produce visible leaks inside. Book a Level 2 inspection and you’ll see the footage yourself. Call (980) 580-8641.
Chimney Liner & Rebuild in Camas

Chimney liner and rebuild work in Camas is pushed by two local realities: original clay liners in the pre-1950s downtown homes are often cracked well beyond safe operation, and the factory-built units on the hillsides were not built to last the wet, wind-driven exposure they get. A cracked liner in a masonry chimney allows heat and gases to reach the surrounding structure, which is a chimney fire waiting on the right spark. When a liner is gone, the chimney has to be relined or rebuilt before it is safe to burn. Our liners come from manufacturers like Olympia Chimney and Copperfield, sourced through Haven’s buying network to keep pricing predictable. The full Chimney Liner & Rebuild scope is explained on the hub page.
Stainless Steel Liner
Signs you need it
When the camera shows clay tile pieces missing from the flue wall, or the old liner has separated at the joints, the safe repair is a continuous stainless steel liner dropped through the full height.
What it costs in Camas
A stainless steel liner installed in a Camas masonry chimney typically runs $2,500 to $5,500, with the final number driven by flue height and access from the roof.
How we do it
We measure the full run, size the liner to the appliance, insulate where the clearance requires it, and verify the installation with a final camera pass.
Liner Replacement
Signs you need it
If the existing liner is rusted through, delaminating, or the flue is no longer sized correctly for the appliance, replacement is the only safe path, and we document why with photos.
What it costs in Camas
Liner replacement in Camas falls in the $2,300 to $5,200 range depending on whether it is a prefab or masonry chimney, and we quote the replacement in writing before ordering any material.
How we do it
We pull the old liner or cut out the damaged section, inspect the surrounding chase or masonry for hidden damage, and install the new liner with a final camera scan for record.
What Chimney Liner & Rebuild Costs in Camas
| Item | Typical range in Camas |
|---|---|
| Stainless steel liner (installed) | $2,500 - $5,500 |
| Liner replacement | $2,300 - $5,200 |
| Partial chimney rebuild | $3,000 - $8,000 |
Do I really need a new liner, or is this an upsell?
You should never take a liner recommendation without seeing the camera footage yourself. We show you the cracked tile, the rust-through, or the separation before we quote anything. If you have a competitor’s written recommendation, bring it for a free second opinion. Call (980) 580-8641.
What happens if I skip a cracked liner in Camas?
Heat and combustion gases move through the gaps into the home’s structure or adjacent wood framing. The risk is a chimney fire or carbon monoxide intrusion. Liner damage does not self-heal, and the wet Camas winters make it worse each year. Call (980) 580-8641.
Brands We Service in Camas

We stock parts from Gelco for factory-built units, Olympia Chimney for liners and caps, and Famco for termination and chase components. Most replacement parts are on our trucks the day we arrive, which keeps a two-visit job from becoming three. See our brands for the full roster and why we source through Haven’s buying network.
Pricing for Chimney Cleaning in Camas, WA
| Service | Typical range in Camas |
|---|---|
| Standard sweep with Level 1 inspection | $189 - $319 |
| Creosote removal | $220 - $380 |
| Soot removal | $189 - $250 |
| Level 2 inspection (standalone) | $250 - $400 |
| Mortar repointing (partial) | $800 - $2,500 |
| Flashing repair | $400 - $1,400 |
| Chimney waterproofing | $600 - $1,800 |
| Stainless steel liner (installed) | $2,500 - $5,500 |
| Liner replacement | $2,300 - $5,200 |
| Partial chimney rebuild | $3,000 - $8,000 |
In Camas, two local factors push prices toward the higher side of each range: steep roof pitches on the hillside homes, which add safety rigging and access time, and the heavy tar-glazed creosote from damp-air burning, which takes longer to remove. Whatever the final number, it is written down and agreed before we start work, so the price on the page is the price you pay.
Neighborhoods We Serve in Camas

We work across every corner of Camas. Scheduling in this area is straightforward, with most appointments available within the same week when called in advance, and afternoon slots are easier to hold on the hillside routes than early mornings.
- Prune Hill
- Downtown Camas
- Grass Valley
- Lacamas Shores
- Green Mountain
Service Area - Cities Near Camas
Beyond Camas, our crews cover the surrounding Clark County and South Sound communities. We frequently schedule work in Vancouver, WA and Puyallup, WA, and the team has regular routes as far north as University Place, WA and Tacoma, WA. Dispatch and scheduling are coordinated from our Seattle office, but the crew serving your Camas neighborhood is local to the route.
Serving Camas, WA - Our Local Coverage Area

We’re based in the Camas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Camas
For most chimney cleaning and liner replacement work, no permit is required in Camas. Rebuilding a chimney from the roofline up may trigger a structural permit, and we flag that before the quote so there are no surprises from the city. Call (980) 580-8641 and we’ll tell you what your specific property needs.
Most Camas appointments are scheduled within five to seven business days during October and November, with earlier availability in summer. Since Gorge weather gets worse into December, booking in September avoids the worst backlog. Call (980) 580-8641 for current scheduling in your neighborhood.
Yes, we service homes throughout Camas, including Prune Hill HOAs and gated subdivisions. If your HOA needs the written scope or photo record before approving exterior work, we provide both as part of the standard job. Call (980) 580-8641 and we’ll coordinate with your HOA directly.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Camas Customers Say
"Found a bird nest and a blocked flue we had no idea about. Photographed everything, cleared it, and explained what the smell had been."
- Curtis V."They told me the flue was fine and I did not need a liner. Charged me for the inspection and nothing else. That is why I have called them twice since."
- Hal M."Cap and crown replaced after water was getting in. Price was quoted in writing, and they showed me the mortar failure first."
- Neil O.





Before
After
Before
After