Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Cleaning in Bloomfield, NJ
Chimney cleaning in Bloomfield typically costs $189-$289 for a standard sweep with a Level 1 inspection, and $289-$489 when a camera-scan Level 2 inspection is added. Most Bloomfield homes need more than a sweep, though. The borough’s 1920s-1940s colonials and two-family houses were built for coal and oil heat, then converted to gas decades later without relining, which means our crews spend as much time documenting liner condition as they do removing creosote. Call (980) 580-8641 for a written quote before any work begins.
Why Bloomfield Homes Are Different
Bloomfield’s housing stock runs overwhelmingly to interwar construction: brick colonials, cape cods, and two-family duplexes packed into Essex County’s inner ring. The original full-masonry chimneys on these homes predate modern liner requirements by half a century. Many were sized for coal-fired furnaces, which means the flue is often too large for the gas appliance venting through it today. An oversized flue cools combustion gases too quickly, producing condensation that eats at the interior masonry. Combine that with Northern New Jersey’s freeze-thaw cycles, and you get the precise failure pattern we see on Bloomfield jobs: spalled mortar joints, cracked crowns, and clay tile liners with hairline fractures that widen every March.
There’s also the two-family factor. In Bloomfield’s duplexes, a single chimney stack frequently carries separate flues for two different households. Neither owner nor tenant tends to claim responsibility for the chimney, so we routinely find stacks that haven’t been touched in five or more years. Some have both flues improperly sharing one tile liner, which is a carbon monoxide hazard and a violation of current NJ fuel gas code. Our camera-scan documentation, standard on every visit under Clause 4 of the Haven Standard, gives both households a clear written record of what their shared stack actually looks like.
Our Main Bloomfield Services
Chimney cleaning is where most Bloomfield homeowners start, but the two services people call about most once the camera comes back up are these:
Fireplace Services in Bloomfield
Bloomfield’s older colonials usually have a masonry fireplace on the main floor, and after decades of use, the firebox and smoke chamber show it. We inspect the firebox for cracked refractory panels, check the damper’s seal, and document the smoke chamber, which is the oddly shaped area above the firebox that most sweeps never photograph. In Bloomfield’s tightly built two-families, a poorly drafting fireplace is often a sign of shared-flue problems above, not just a dirty chimney. Full details are on our Fireplace Services in Bloomfield page.

Chimney Cap & Crown in Bloomfield
The crown is the concrete slab on top of your chimney, and in Bloomfield it takes a beating every winter. Freeze-thaw cycles crack the crown, water gets in, and the mortar joints below start spalling. A missing or damaged cap lets rain pour straight down the flue, which accelerates liner deterioration. We replace cracked crowns, install or repair caps, and waterproof the top of the stack before the next freeze cycle does more damage. See Chimney Cap & Crown in Bloomfield for local pricing and what to look for.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterChimney Cleaning & Sweep in Bloomfield

A standard chimney sweep in Bloomfield runs $189-$289, and we recommend a Level 2 camera inspection alongside it for $289-$489 total on older homes. Why the camera matters here specifically: the average Bloomfield chimney was built in the 1930s for coal, and if it hasn’t been relined, you need to know the clay tile’s actual condition before burning anything. Our Chimney Cleaning & Sweep service always includes documentation, so you see what we see.
Level 1 Inspection
Signs you need it
You burn wood or gas regularly and it’s been more than a year since anyone looked at the flue, or you just bought the house and have no record of the chimney’s condition.
What it costs in Bloomfield
A Level 1 inspection in Bloomfield is included with a standard sweep at $189-$289, or $99-$149 on its own.
How we do it
We check the accessible portions of the flue, firebox, damper, and exterior stack, then document the condition in writing with photos added to your file.
Level 2 Inspection
Signs you need it
You’re buying or selling a Bloomfield home, the house has changed fuel types since the chimney was built, there was a chimney fire, or you haven’t used the fireplace in years and want to start.
What it costs in Bloomfield
A Level 2 inspection with full camera scan runs $189-$289 in Bloomfield when added to a sweep, and $289-$489 as a standalone service.
How we do it
We run a video camera down the entire flue length, photograph every section including the smoke chamber and crown, and hand you a written report with the images.
Creosote Removal
Signs you need it
You see black, shiny, or crusty buildup on the firebox walls, smoke backs up into the room, or the fireplace smells strongly even when cold.
What it costs in Bloomfield
Creosote removal in Bloomfield runs $189-$289 for Class I or II deposits, with Class III glazed creosote priced per job after camera assessment.
How we do it
We use rotary wire brushes and specialty chemical treatments to break down the deposits, then vacuum the debris out and photograph the result.
Soot Removal
Signs you need it
Your oil or gas appliance vents through the chimney and you see fine black dust around the firebox or the flue hasn’t been cleaned in two or more heating seasons.
What it costs in Bloomfield
Soot removal for gas or oil appliance flues in Bloomfield typically costs $189-$289 depending on the flue’s length and access.
How we do it
We brush the full flue length, remove the soot from the smoke chamber and cleanout, and document the appliance connector’s condition in the photo record.
What Chimney Cleaning & Sweep Costs in Bloomfield
| Item | Typical range in Bloomfield |
|---|---|
| Standard sweep with Level 1 inspection | $189-$289 |
| Sweep with Level 2 camera inspection | $289-$489 |
| Creosote removal (Class I-II) | $189-$289 |
How often should I have my Bloomfield chimney cleaned?
Every year if you burn wood, and every one to two years for gas or oil appliance flues. Bloomfield’s older chimneys accumulate deposits faster because oversized flues cool exhaust too quickly, which condenses creosote and soot on the walls.
Do I really need a camera inspection if the chimney looks fine from outside?
Yes, especially in Bloomfield. The outside brick can look solid while the clay tile liner inside is cracked, shifted, or missing entirely. The only way to confirm is a camera scan. We include photo documentation on every visit.
Chimney Repair in Bloomfield

Chimney repair in Bloomfield usually means fixing what water and freeze-thaw cycles have already damaged in the masonry. Mortar repointing runs $900-$2,500 depending on stack height and access, and most Bloomfield chimneys we see need some repointing or crown work within five years of the first camera inspection. Our Chimney Repair service always starts with a written scope and price before any work begins.
Mortar Repointing
Signs you need it
You can scrape mortar out from between the bricks with a fingernail, or you see gaps and missing joints on the stack above the roofline.
What it costs in Bloomfield
Mortar repointing in Bloomfield typically runs $900-$2,500 depending on how much of the stack needs work and how tall the chimney is.
How we do it
We grind out the deteriorated mortar to a proper depth, pack in fresh mortar matched to your brick’s original strength, and tool the joints to shed water.
Chimney Waterproofing
Signs you need it
Your chimney soaks up water and stays dark after rain, you see efflorescence (white powdery stains) on the brick, or moisture is working its way into the attic around the stack.
What it costs in Bloomfield
Chimney waterproofing in Bloomfield runs $600-$1,200 for a full stack application, including surface prep and a breathable masonry sealant.
How we do it
We clean the brick surface, repair any minor cracks or spalled areas, then apply a vapor-permeable waterproofing treatment that lets the masonry breathe while blocking water absorption.
What Chimney Repair Costs in Bloomfield
| Item | Typical range in Bloomfield |
|---|---|
| Mortar repointing | $900-$2,500 |
| Chimney waterproofing | $600-$1,200 |
| Flashing repair | $400-$900 |
Can cracked mortar really cause a chimney fire?
Yes. Gaps in the mortar joints let heat and embers reach the wood framing around the chimney chase. In Bloomfield’s older homes, that framing is usually dry, century-old timber. Repointing closes those gaps and restores the fire-resistant barrier.
How do I know if my chimney needs repointing or a full rebuild?
The honest answer comes from a camera inspection and a close look at the brick. If the bricks themselves are spalling, cracked through, or the stack is visibly leaning, rebuild is needed. If the bricks are sound but the mortar is soft, repointing is enough. We’ll show you the photos and give you a written recommendation either way.
Chimney Liner & Rebuild in Bloomfield

Chimney liner and rebuild work in Bloomfield is often the difference between a chimney that works safely and one that leaks exhaust into the house. A stainless steel liner installation runs $2,500-$5,000 on a typical Bloomfield colonial, while a full chimney rebuild from the roofline up can run $8,000-$18,000 depending on height and access. Our Chimney Liner & Rebuild service uses DuraFlex and HeatShield materials, and every job starts with a camera-scan inspection and a written scope.
Stainless Steel Liner
Signs you need it
Your Bloomfield home was built before 1940 and still has its original clay tile liner, or the camera scan shows cracked, shifted, or missing tile sections.
What it costs in Bloomfield
A stainless steel liner for a typical Bloomfield chimney runs $2,500-$5,000, including the liner, insulation, top plate, and rain cap.
How we do it
We measure the flue, size the liner to match your appliance’s venting requirements, drop the liner down the full length, insulate it, and connect it at the breach and the top.
Full Chimney Rebuild
Signs you need it
The stack above the roofline is leaning, bricks are spalling through their faces, or large sections of mortar are missing and the chimney moves when you press on it.
What it costs in Bloomfield
A full chimney rebuild from the roofline up in Bloomfield typically runs $8,000-$18,000 depending on the stack’s height and the roofing configuration around it.
How we do it
We dismantle the damaged stack down to sound masonry, rebuild it with new brick or CMU blocks sized to match, install a new crown and cap, and flash everything properly.
What Chimney Liner & Rebuild Costs in Bloomfield
| Item | Typical range in Bloomfield |
|---|---|
| Stainless steel liner | $2,500-$5,000 |
| Liner replacement | $3,000-$6,500 |
| Full chimney rebuild | $8,000-$18,000 |
Is a stainless steel liner really necessary if I only have a gas furnace?
Yes, and in Bloomfield it’s one of the most common code issues we find. Gas exhaust is cooler than oil or wood exhaust, which creates condensation that attacks masonry from the inside. Modern NJ fuel gas code requires a properly sized liner. Without one, you risk carbon monoxide leaking through cracked tile into the house.
Can my chimney be relined without tearing it down?
Usually yes. If the masonry shell is structurally sound, we can drop a stainless steel or HeatShield liner down the existing flue without removing any brick. The camera scan tells us whether the shell is sound enough to keep. We show you the footage before recommending anything.
Brands We Service in Bloomfield

We stock and install liners, caps, and repair materials from DuraFlex, HeatShield, Gelco, and Copperfield. Parts for standard Bloomfield flue sizes are usually on the truck, which means no second trip for common liner and cap replacements. Full details are on our brands page.
Pricing for Chimney Cleaning in Bloomfield, NJ
| Service | Typical range in Bloomfield |
|---|---|
| Standard sweep with Level 1 inspection | $189-$289 |
| Sweep with Level 2 camera inspection | $289-$489 |
| Creosote removal (Class I-II) | $189-$289 |
| Soot removal | $189-$289 |
| Level 1 inspection (standalone) | $99-$149 |
| Level 2 inspection (standalone) | $289-$489 |
| Mortar repointing | $900-$2,500 |
| Chimney waterproofing | $600-$1,200 |
| Flashing repair | $400-$900 |
| Stainless steel liner | $2,500-$5,000 |
| Liner replacement | $3,000-$6,500 |
| Full chimney rebuild | $8,000-$18,000 |
What pushes a Bloomfield quote toward the top of these ranges is usually chimney height and roof access. A three-story colonial on a steep pitch costs more to scaffold and work than a single-story cape. The written price we give you before work starts includes everything: labor, materials, cleanup, and the photo record. No surprises, no handshake add-ons.
Neighborhoods We Serve in Bloomfield

We work throughout Bloomfield, from the older housing around Brookdale Park down to the town center and the neighborhoods along the Garden State Parkway corridor. Our crews know which blocks have the two-family stacks and which have the taller post-war chimneys, and the difference matters for equipment and access.
- Brookdale
- Watsessing
- Oakland
- North Center
- Bloomfield Center
Service Area - Cities Near Bloomfield
Emberly Chimney Cleaners serves Bloomfield and the surrounding Essex County communities. We also work regularly in Belleville, NJ, Montclair, CA, Nutley, NJ, and East Orange, NJ. Dispatch and scheduling are coordinated from our New York City office, and crews serve Bloomfield locally with equipment staged nearby.
Serving Bloomfield, NJ - Our Local Coverage Area

We’re based in the Bloomfield area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Bloomfield
Most Bloomfield appointments are scheduled within a week to ten days. Fall is our busiest season because homeowners want the chimney ready before burning season, so booking in late summer or early fall gets you the best availability. Call (980) 580-8641 and we’ll give you a written quote and a firm date.
Most chimney cleaning, inspection, and liner work does not require a Bloomfield building permit. Full chimney rebuilds or structural repairs above a certain scope may need one, and we handle that paperwork for you as part of the written scope. We’ll tell you upfront if your job requires anything beyond the standard work.
Every Bloomfield job includes a written scope, a written price, and a documented photo record of the work. Clause 4 of the Haven Standard requires the camera footage and still photos be archived in your file, and you get a copy. If you ever sell the house, that record transfers to the new owner.
If you’re in Bloomfield and want a chimney that’s actually documented, not just swept, call (980) 580-8641. We’ll give you a written price before any work starts, and you’ll see the photos of what we found.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bloomfield Customers Say
"Found a bird nest and a blocked flue we had no idea about. Photographed everything, cleared it, and explained what the smell had been."
- Curtis V."They told me the flue was fine and I did not need a liner. Charged me for the inspection and nothing else. That is why I have called them twice since."
- Hal M."Cap and crown replaced after water was getting in. Price was quoted in writing, and they showed me the mortar failure first."
- Neil O.





Before
After
Before
After