Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterChimney Cleaning in Alpharetta, GA
Chimney cleaning in Alpharetta typically costs $189-$349 for a standard sweep with a Level 1 inspection, and most jobs are completed in under two hours. What sets Alpharetta apart is what we find inside the flue: because these large 1990s and 2000s executive homes in subdivisions like Windward were built almost entirely with factory-built zero-clearance fireplaces, we’re not just sweeping creosote. We’re also documenting refractory panel condition, checking chase tops, and flagging the cascade damage that happens when two or three flues share one exterior chase. Call (980) 580-8641 and we’ll give you a written price before anyone shows up.
Why Alpharetta Homes Are Different
Alpharetta’s building boom along the GA-400 tech corridor put up thousands of large homes between roughly 1988 and 2008, and the builders standardized on prefabricated fireplace systems. Brands like Heatilator and Heat & Glo dominate, and those units have an expected service life of about 20 to 30 years. In Alpharetta right now, that window is closing all at once, which is why our techs routinely see warped fireboxes, crumbling refractory panels, and flue components that cannot be relined and must be replaced outright. The homes are big, often with two to four fireplaces each: a formal living room unit, a keeping-room unit, and frequently a basement or master-suite fireplace. That means a single property can have multiple aging systems reaching failure around the same time.
The climate adds a second layer. Alpharetta’s piedmont winters are mild, so most homeowners light fires only a handful of times each season. Creosote accumulation stays light. But those idle, uncapped chimneys sit open for months of warm weather, which makes them nesting habitat for chimney swifts, a federally protected species under the Migratory Bird Treaty Act, and for raccoons. Animal exclusion and stainless cap installation become urgent heading into fall, and any active swift nesting means we pause work until the birds leave. That’s a scheduling reality specific to Alpharetta and the surrounding north Fulton County area.
A third pattern shows up often in Windward and Northwinds-era construction: builders ran two or three flues side-by-side inside a single exterior chase. A missing cap on one flue channels rainwater directly into the adjacent ones, accelerating panel failure across every unit at once. We’ve documented this cascade-damage pattern repeatedly in Alpharetta, and it’s far less common in older single-flue masonry homes elsewhere in metro Atlanta.
Our Main Alpharetta Services
Alpharetta homeowners call us most often about two things beyond the sweep itself: fireplace systems that won’t draft or have visible interior damage, and chimney caps or crowns that have failed and are letting water into the chase. Both are common consequences of the aging prefab stock in this city.
Fireplace Services in Alpharetta
Fireplace repair and replacement in Alpharetta usually traces back to a zero-clearance unit that has exceeded its rated service life. Refractory panels crack, the firebox warps, and the unit can no longer be safely operated. We inspect the firebox, damper, refractory panels, and gas log set if present, then show you photos of exactly what we found. If the unit needs replacement, we quote it in writing before any work begins. See Fireplace Services in Alpharetta for the full scope.
Chimney Cap & Crown in Alpharetta
A missing or rusted-out cap is the single most common entry point for water in Alpharetta’s multi-flue chases. When one flue is exposed, rain and debris drop directly into the shared chase and onto adjacent flues, so a small cap problem becomes a whole-system problem quickly. We install stainless caps sized to the flue and repair or rebuild chase tops and crowns. See Chimney Cap & Crown in Alpharetta for pricing and scope.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterChimney Cleaning & Sweep in Alpharetta
A chimney sweep in Alpharetta is as much about documentation as it is about removing soot. Our camera-scan inspection, standard on every visit since 2009, tells you whether the fireplace is safe to light and whether the flue is degrading. That matters here because so many Alpharetta homes run factory-built systems that cannot be relined like masonry: if the panels are cracked or the firebox is warped, the fix is usually replacement, not a sweep. For the full scope of our Chimney Cleaning & Sweep service, we walk the flue with a camera and give you a written photo record before we leave.
Level 1 Inspection
Signs you need it
If you have used the fireplace at all in the past year, or if you are buying a home and the seller cannot produce a recent inspection, schedule a Level 1.
What it costs in Alpharetta
Our Level 1 inspection runs $99-$249 and is included with a standard sweep.
How we do it
We check the accessible portions of the fireplace, flue, damper, and exterior chimney, and we document the condition with photos.
Level 2 Inspection
Signs you need it
If you have changed fuel type, had a chimney fire, or are selling the home, a Level 2 inspection with camera scan is the right call.
What it costs in Alpharetta
A Level 2 inspection in Alpharetta runs $249-$449 and includes the full camera-scan record.
How we do it
We run a camera down the flue and through the accessible areas, photographing every section and noting gaps, cracks, or damage in writing.
Creosote Removal
Signs you need it
If the flue has thick, shiny, or tar-like buildup, that is Class II or Class III creosote and it is a fire hazard.
What it costs in Alpharetta
Creosote removal in Alpharetta runs $189-$349 depending on buildup class and flue length.
How we do it
We use rotary brushes and hand tools matched to the flue type, then camera-check the flue to confirm the creosote is gone.
Soot Removal
Signs you need it
Powdery black dust on the damper, firebox walls, or visible when you run a finger along the flue means soot has accumulated past the point of normal use.
What it costs in Alpharetta
Soot removal runs $149-$249 and is typically paired with a standard sweep.
How we do it
We brush the flue and firebox, vacuum with a HEPA-filtered unit, and document the result with before-and-after photos.
Annual Sweep
Signs you need it
If the fireplace has been used even a few times since the last cleaning, or if the flue has not been swept in over a year, book the annual sweep.
What it costs in Alpharetta
An annual sweep with inspection runs $189-$349 in Alpharetta.
How we do it
We sweep the flue, check the firebox and damper, and hand you a written record with photos of the cleaned flue and any findings.
What Chimney Cleaning & Sweep Costs in Alpharetta
| Item | Typical range in Alpharetta |
|---|---|
| Standard sweep with Level 1 inspection | $189 - $349 |
| Level 2 camera-scan inspection | $249 - $449 |
| Animal or debris removal (varies) | $125 - $400 |
How often should a chimney be swept in Alpharetta?
Once a year, even with light use. Most Alpharetta homes burn only a few fires per season, but the open flue collects nesting material and debris during the long warm months, so an annual check catches animal entry before it becomes damage.
Do prefab fireplaces need a different kind of sweep?
Yes. Zero-clearance units cannot be treated like masonry flues, and sweeping them with the wrong tools destroys the refractory panels. We match our brushes and cameras to the specific flue type and document panel condition on every job.
Call (980) 580-8641 for a written quote on any of these services.
Chimney Repair in Alpharetta
Most chimney repair calls in Alpharetta come back to water intrusion and aging materials, not fire damage. The large 1990s and 2000s homes here have exterior chases with multiple flues, and when one cap fails or flashing separates, water works its way into every adjacent system. You get spalling brick, rusted dampers, and cracked crowns, and the damage compounds quickly. Our Chimney Repair work starts with a camera-scan inspection to pinpoint exactly what needs attention, so you see the evidence before you approve anything.
Mortar Repointing
Signs you need it
Crumbling, missing, or recessed mortar joints in the chimney stack let water into the masonry and widen the damage every freeze-thaw cycle.
What it costs in Alpharetta
Repointing in Alpharetta runs $1,200-$2,800 depending on the area and joint depth.
How we do it
We grind out the failing joints, pack in new mortar matched to the original, and photo-document the repair before and after.
Spalling Brick Repair
Signs you need it
Flaking, pitted, or broken brick faces mean water has penetrated the masonry and the brick is failing from the inside out.
What it costs in Alpharetta
Spalling brick repair runs $500-$1,800, or $20-$40 per brick for individual replacements.
How we do it
We remove the damaged brick, replace it with a matched unit, and seal the repair so water stops entering the stack.
Chimney Waterproofing
Signs you need it
Dark staining, efflorescence, or repeated spalling after previous repairs means the masonry is absorbing water and needs a vapor-permeable sealant.
What it costs in Alpharetta
Waterproofing a chimney in Alpharetta runs $500-$1,500 depending on stack height and access.
How we do it
We clean the masonry, apply a breathable silane-siloxane waterproofing agent, and give you a written record of the application.
Flashing Repair
Signs you need it
Water staining on the ceiling near the chimney, rust streaks on the exterior, or a leak after rain points to failed flashing at the roofline.
What it costs in Alpharetta
Flashing repair runs $450-$1,600 in Alpharetta, depending on whether we repair or fully replace the flashing.
How we do it
We remove the old flashing, install new metal lapped under the shingles and into the mortar, and seal every joint before documenting the fix.
Chimney Rebuilding
Signs you need it
A leaning stack, large missing sections of brick, or a chimney that has pulled away from the house means partial or full rebuilding is required.
What it costs in Alpharetta
Partial rebuilding runs $100-$250 per brick or $2,000-$6,000 for a section; a full rebuild runs $7,000-$14,000.
How we do it
We safely demo the unstable section, rebuild with new brick and mortar, and document every stage with photos for your record.
What Chimney Repair Costs in Alpharetta
| Item | Typical range in Alpharetta |
|---|---|
| Mortar repointing | $1,200 - $2,800 |
| Spalling brick repair | $500 - $1,800 |
| Flashing repair | $450 - $1,600 |
Do I really need to repair spalling brick right away?
Not always immediately, but the longer it goes, the more brick you lose. Spalling is water damage, and in Alpharetta’s multi-flue chases, one damaged section becomes a pathway for water into adjacent flues. Get it inspected and decide from photos.
Can you repair a prefab fireplace flue like a masonry one?
No. Factory-built flues cannot be repointed or relined the same way a masonry flue can. If the panels or firebox are compromised, replacement is usually the only safe option. We will show you the camera evidence either way.
Call (980) 580-8641 and we’ll put the repair scope and price in writing.
Chimney Liner & Rebuild in Alpharetta
Liner and rebuild work in Alpharetta splits two ways. Masonry chimneys can often be relined with a stainless system, but the prefab zero-clearance units that dominate this city cannot: when their refractory panels go, the whole system is replaced. That distinction drives most of the quotes we write here. We use Chimney Liner & Rebuild materials from DuraFlex and HeatShield, and every job gets a camera-scan record before and after the work.
Stainless Steel Liner
Signs you need it
Flue tile cracks, missing mortar joints, or a masonry chimney that has never been relined and is venting a furnace or water heater needs a stainless liner.
What it costs in Alpharetta
A stainless liner in Alpharetta runs $2,500-$5,000 installed for a standard single-flue masonry chimney.
How we do it
We size the liner to the appliance and flue, lower it down, insulate as needed, and secure it at the top with a new cap and flashing.
Flexible Liner
Signs you need it
An offset or irregular masonry flue that cannot take a rigid liner without major demolition is a candidate for a flexible stainless liner.
What it costs in Alpharetta
A flexible liner installation runs $1,500-$3,500 in Alpharetta for a single flue.
How we do it
We pull the flexible liner through the existing flue path, attach it at the appliance and the cap, and verify the connection with a camera scan.
Liner Replacement
Signs you need it
A rusted-through, perforated, or collapsed liner that can no longer safely vent exhaust gases must be pulled and replaced.
What it costs in Alpharetta
Liner replacement runs $1,500-$5,000 depending on flue length, liner type, and access.
How we do it
We remove the old liner, inspect the flue interior, and install a new sized liner with a new cap, then document the completed job.
Partial Rebuild
Signs you need it
If the top courses of brick or the crown have failed but the lower stack is sound, a partial rebuild addresses the damaged section.
What it costs in Alpharetta
Partial rebuilding in Alpharetta runs $2,000-$6,000 depending on height and access.
How we do it
We demo the deteriorated section, rebuild it with new brick and a poured crown, and flash every joint before documenting the work.
Full Chimney Rebuild
Signs you need it
A chimney that leans, has massive spalling throughout, or has separated from the house needs a full rebuild from the roofline up.
What it costs in Alpharetta
A full rebuild in Alpharetta runs $7,000-$14,000, depending on height, access, and brick matching requirements.
How we do it
We scaffold, demo the old stack, rebuild with new brick and mortar, install a new crown and cap, and photograph every stage.
What Chimney Liner & Rebuild Costs in Alpharetta
| Item | Typical range in Alpharetta |
|---|---|
| Flexible liner installation | $1,500 - $3,500 |
| Stainless liner installation | $2,500 - $5,000 |
| Prefab system replacement | $3,000 - $8,000+ |
Can my prefab fireplace be relined?
No. Factory-built zero-clearance units in Alpharetta cannot be relined; the entire system is certified as a unit, and once the panels or firebox fail, replacement is required. We will show you the camera evidence before any recommendation.
What actually happens if I skip a liner repair?
Exhaust gases can leak into the chase or the house, and carbon monoxide can accumulate. In a three-flue chase, one failed liner also damages the adjacent flues. The camera scan shows whether you can wait or need to act now.
Call (980) 580-8641 and we’ll give you a written price on liner or rebuild work.
Brands We Service in Alpharetta
We work on and install parts from our brands including HeatShield, DuraFlex, Copperfield, and Famco. We keep common flue components and caps in local stock for faster turnaround on Alpharetta jobs, and we source replacement panels and fireboxes directly from manufacturers so you’re not waiting weeks on a special order.
Pricing for Chimney Cleaning in Alpharetta, GA
| Service | Typical range in Alpharetta |
|---|---|
| Annual sweep with Level 1 inspection | $189 - $349 |
| Level 2 camera-scan inspection | $249 - $449 |
| Creosote removal | $189 - $349 |
| Soot removal | $149 - $249 |
| Animal or debris removal | $125 - $400 |
| Chimney cap installation | $300 - $900 |
| Mortar repointing | $1,200 - $2,800 |
| Spalling brick repair | $500 - $1,800 |
| Flashing repair | $450 - $1,600 |
| Flexible liner installation | $1,500 - $3,500 |
| Stainless liner installation | $2,500 - $5,000 |
| Prefab system replacement | $3,000 - $8,000+ |
What pushes prices up in Alpharetta is access and chase complexity: a third-floor chimney on a steep lot, or a three-flue chase that requires scaffold work, will land at the higher end of these ranges. Every quote we write is fixed before work starts, with the scope and warranty in writing under Clause 1 of the Haven Standard.
Neighborhoods We Serve in Alpharetta
Our crews work throughout Alpharetta weekly, and because we dispatch locally, typical response time for a booked inspection is one to three business days.
- Windward and Northwinds subdivisions
- Kingsridge and Country Club of the South area
- Cambridge and Crooked Creek
- Fairfax and Farmbrook
- Providence and the Rucker Road corridor
Service Area - Cities Near Alpharetta
Beyond Alpharetta, our crews cover the north metro area regularly, including Roswell, GA, Duluth, GA, and Woodstock, GA. We also schedule group visits to Canton, MA for our New England clients. If you’re in a neighboring community, call us and we’ll confirm the next available date in your area.
Serving Alpharetta, GA - Our Local Coverage Area
We’re based in the Alpharetta area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Alpharetta
Most inspections and cleanings are scheduled within one to three business days. We coordinate from our Atlanta dispatch office, and crews serve Alpharetta locally throughout the week. Call (980) 580-8641 and we’ll give you a written quote and a firm date before you commit.
Many Windward and Northwinds HOAs require exterior work to match existing materials and finishes, and some require approval before a full rebuild or cap replacement. We provide the written scope and photos you need for your HOA submittal at no extra charge.
Yes. Federal law protects chimney swifts and their nests under the Migratory Bird Treaty Act, so we do not remove active nests and will reschedule the sweep until the birds have left. In Alpharetta, nesting season runs from spring through late summer, so fall openings fill up fast. Call early if you want a pre-season slot.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Alpharetta Customers Say
"Gas insert service done properly with the readings written down. The technician had the certification number printed on the paperwork."
- Bettina A."We were buying the house and needed a real inspection. The report had photographs, the standard it was done to, and a clear repair figure. The seller paid for the repair."
- Lorna D."They ran a camera down the flue and showed me the cracked tiles on a screen. The previous company had swept it twice and never mentioned it."
- Gregory F.