Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Cleaning in Lynnwood, WA
Chimney cleaning in Lynnwood typically costs $189 to $319 for a standard sweep with a Level 1 inspection, and $289 to $449 when a camera scan is included. If you need a sweep, call (980) 580-8641 and we’ll give you a written price before any work starts.
Why Lynnwood Homes Are Different
Lynnwood incorporated in 1959 and built out fast through the 1960s and 70s as a Boeing-era bedroom community. That means block after block of the same vintage masonry chimneys, most with clay tile flue liners now 50 to 60 years old and rarely upgraded. The wet marine climate does something specific to those chimneys. Roughly 37 inches of annual rainfall and persistently high humidity keep mortar joints damp, which accelerates deterioration and invites moss and lichen onto exposed brick crowns. Moisture works its way into flue tiles between burns.
The mild Puget Sound winters create a second problem. Homeowners here burn infrequently and at low temperatures, which means flue gases rarely get hot enough to fully pyrolyze creosote. Instead of the dry, flaky deposits common in colder inland markets, Lynnwood chimneys accumulate sticky, wet Stage 2 creosote. It is heavier, more hazardous, and harder to remove than what homeowners expect. We see it even in chimneys used only a handful of times each season.
Our Main Lynnwood Services
Most Lynnwood homeowners call us first about their fireplace or the cap and crown sitting exposed to the rain. Here is what each involves.
Fireplace Services in Lynnwood
A surprising share of Lynnwood’s 1960s and 70s homes have factory-built zero-clearance metal fireplaces rather than true masonry systems. Many are now well past their 20 to 30 year design life, and owners frequently misidentify them as masonry. We inspect, clean, and repair both types, and we tell you plainly when a metal unit needs replacement rather than another service call. Fireplace Services in Lynnwood covers the full scope.

Chimney Cap & Crown in Lynnwood
The crown is the concrete slab that caps a masonry chimney, and in Lynnwood it takes a beating from rain and moss. A cracked crown lets water into the flue and the mortar bed below, which is how small problems become full rebuilds. We replace crowns, install properly sized caps, and repair flashing in the same visit when it makes sense. Chimney Cap & Crown in Lynnwood explains the work and the material choices.

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterChimney Sweep in Lynnwood

Chimney sweep in Lynnwood means removing the sticky Stage 2 creosote that this climate produces, not the dry powder found in colder markets. On a 1960s or 70s home with its original clay tile liner, that creosote builds up faster than homeowners expect, and it takes mechanical brushing to get it off the flue walls. Every visit includes a camera scan and a documented photo record under Clause 4 of the Haven Standard, so you see exactly what we found and what we left behind. For the full service breakdown, see Chimney Sweep.
Level 1 Inspection
Signs you need it
You use your fireplace every season and nothing has changed, but it has been more than a year since anyone looked inside the flue.
What it costs in Lynnwood
A Level 1 inspection runs $149 to $249 and is included with any standard sweep.
How we do it
We check the accessible portions of the chimney inside and out, confirm the flue is unobstructed, and document basic condition with photos.
Level 2 Inspection
Signs you need it
You bought the home recently, changed fuel type, had a chimney fire, or the house just went through a seismic event.
What it costs in Lynnwood
A Level 2 inspection with camera scan runs $189 to $299 when done on its own, and $99 to $149 when added to a sweep.
How we do it
We run a camera down the full length of the flue, document every joint and tile, and give you the footage with the written report.
Creosote Removal
Signs you need it
You see dark, shiny, or flaky buildup on the flue walls, or the fireplace smells sharp and acrid when the weather warms up.
What it costs in Lynnwood
Glazed Stage 2 creosote removal in Lynnwood runs $229 to $449 depending on flue condition and buildup thickness.
How we do it
We use rotary loops and chemical treatments that break down the sticky creosote this climate produces, then sweep the loosened material out.
Annual Sweep
Signs you need it
You burn more than a cord of wood per season, or your last sweep happened more than 12 months ago.
What it costs in Lynnwood
A standard annual sweep with Level 1 inspection runs $189 to $319 and takes about an hour on a typical Lynnwood ranch chimney.
How we do it
We lay drop cloths, run brushes from the flue top down or the firebox up, and leave the firebox clean with a photo record of the flue after.
What Chimney Sweep Costs in Lynnwood
| Item | Typical range in Lynnwood |
|---|---|
| Level 1 Inspection | $149 - $249 |
| Level 2 Inspection (camera scan) | $189 - $299 standalone, $99 - $149 added to sweep |
| Creosote Removal (Stage 2) | $229 - $449 |
| Standard Annual Sweep | $189 - $319 |
How often should a chimney be swept in Lynnwood?
Every year if you burn at all, and some Lynnwood chimneys need it every six months because the humid climate produces sticky creosote faster than dry climates do. A sweep removes buildup before it becomes a fire hazard.
Do I really need a camera scan with every sweep?
We include it on every visit because it is the only way to see cracked tiles, gaps, or hidden creosote pockets that a visual check from the roof misses. The photo record is yours to keep. Call (980) 580-8641 to book.
Chimney Repair in Lynnwood

Chimney repair in Lynnwood usually starts at the mortar joints, because the persistent rain here works into lime-based mortar and erodes it faster than homeowners expect. On a 1960s or 70s chimney with single-wythe masonry, repointing and waterproofing address the damage before it becomes structural, but we also rebuild crowns and replace flashing where water has already done its work. For the broader scope, see Chimney Repair.
Mortar Repointing
Signs you need it
You can scrape mortar out of the joints with a screwdriver, or the joints look raked and recessed rather than flush with the brick.
What it costs in Lynnwood
Repointing a typical Lynnwood chimney runs $1,200 to $3,500 depending on access and how much of the stack needs work.
How we do it
We grind out deteriorated mortar to a proper depth, pack in new mortar matched to the existing color and profile, and tool it flush.
Spalling Brick Repair
Signs you need it
The brick faces are flaking, popping, or leaving rust-colored dust on the roof or hearth, which means water has gotten inside the brick itself.
What it costs in Lynnwood
Replacing spalled brick runs $400 to $900 for isolated areas and $2,000 to $6,000 when the damage extends across the stack.
How we do it
We remove the damaged brick, match replacements from local suppliers, and bed them in mortar that keeps water out rather than trapping it.
Chimney Waterproofing
Signs you need it
The brick darkens and stays wet for days after rain, or moss and lichen grow directly on the exposed chimney face.
What it costs in Lynnwood
Chimney waterproofing runs $300 to $700 on a standard Lynnwood chimney and extends the life of repointing work by years.
How we do it
We apply a vapor-permeable silane-siloxane treatment that lets moisture escape from inside the brick while blocking rain from getting in.
Flashing Repair
Signs you need it
You see water stains on the ceiling near the chimney, or the flashing has pulled away from the roofline and is no longer sealed.
What it costs in Lynnwood
Flashing repair or replacement runs $500 to $1,800 depending on roof pitch and whether the existing flashing is salvageable.
How we do it
We cut back the old flashing, install new step and counter flashing, and seal every lap with a high-quality polyurethane sealant.
What Chimney Repair Costs in Lynnwood
| Item | Typical range in Lynnwood |
|---|---|
| Mortar Repointing | $1,200 - $3,500 |
| Spalling Brick Repair | $400 - $900 isolated, $2,000 - $6,000 extensive |
| Chimney Waterproofing | $300 - $700 |
| Flashing Repair | $500 - $1,800 |
Can water damage be fixed in the winter?
Yes. Repointing and waterproofing can be done in cold weather with the right mortar additives. The bigger constraint is rain, which is why we schedule repair work in Lynnwood around the dry windows whenever possible.
Do you always recommend waterproofing after repair?
Almost always. Lynnwood’s humidity means bare brick reabsorbs moisture quickly, undoing repointing work within a few seasons. The treatment costs less than redoing the joints. Call (980) 580-8641 for a written quote.
Chimney Liner & Rebuild in Lynnwood

Chimney liner and rebuild work in Lynnwood is driven by the clay tile liners that have been absorbing rain and creosote since the Nixon administration. Cracked or separated tiles cannot be patched safely, and a full rebuild is sometimes the only option when the masonry above the roofline has crumbled past the point of repair. We quote both paths with camera evidence so you can see the condition for yourself. For the full material and method breakdown, see Chimney Liner & Rebuild.
Stainless Steel Liner
Signs you need it
Your clay tiles are cracked, spalled, or missing sections, and the chimney is otherwise structurally sound.
What it costs in Lynnwood
A stainless steel liner installed in a Lynnwood chimney runs $3,000 to $6,500 including the connecting appliance.
How we do it
We size the liner to the flue, drop it in from the top, insulate it, connect it to the appliance, and document every connection with the camera.
Flexible Liner
Signs you need it
The flue has offsets or bends that make a rigid liner impractical, or you are relining an existing wood-burning fireplace with an insert.
What it costs in Lynnwood
A flexible liner system runs $2,800 to $5,800 installed, which includes the connector, termination cap, and insulation.
How we do it
We pull the flexible liner through the existing flue path, secure it at the top and bottom, and insulate the annular space to reduce creosote condensation.
Partial Rebuild
Signs you need it
The top few courses of brick are loose, missing, or leaning, but the chimney below the roofline is solid.
What it costs in Lynnwood
A partial rebuild above the roofline runs $2,500 to $7,000 in Lynnwood, depending on how many courses come down and what is salvageable.
How we do it
We tear down to sound masonry, lay new brick with a proper bond, pour a new crown, and install a correctly sized cap.
Full Chimney Rebuild
Signs you need it
The chimney leans visibly, the masonry is crumbling along its full height, or major structural cracks run through the stack and the flue.
What it costs in Lynnwood
A full rebuild from the roofline up runs $8,000 to $18,000 for a typical Lynnwood single-story chimney.
How we do it
We demolish the existing stack, rebuild with new brick or block, install a new liner, pour a proper crown, and finish with a cap and flashing.
What Chimney Liner & Rebuild Costs in Lynnwood
| Item | Typical range in Lynnwood |
|---|---|
| Stainless Steel Liner | $3,000 - $6,500 |
| Flexible Liner | $2,800 - $5,800 |
| Partial Rebuild (above roofline) | $2,500 - $7,000 |
| Full Chimney Rebuild | $8,000 - $18,000 |
How do I know if I need a liner or a rebuild?
The camera scan answers this. Cracked tiles without structural damage usually mean a liner. Leaning or crumbling masonry means a rebuild. We will not recommend either without showing you the footage.
Does homeowner’s insurance cover a liner replacement?
Sometimes, and only when the cause is sudden damage like a chimney fire or a falling tree, not gradual water intrusion. We document everything so you have evidence for your claim. Call (980) 580-8641 with questions.
Brands We Service in Lynnwood

We install and service parts from DuraFlex, HeatShield, and Copperfield, and keep common liner and flashing components in local stock for Lynnwood jobs. Material availability matters when your flue is exposed. See our brands for the full list and what we use each for.
Pricing for Chimney Cleaning in Lynnwood, WA
| Service | Typical range in Lynnwood |
|---|---|
| Level 1 Inspection | $149 - $249 |
| Level 2 Inspection (camera scan) | $189 - $299 |
| Level 2 added to sweep | $99 - $149 |
| Creosote Removal (Stage 2) | $229 - $449 |
| Standard Annual Sweep | $189 - $319 |
| Mortar Repointing | $1,200 - $3,500 |
| Spalling Brick Repair (isolated) | $400 - $900 |
| Chimney Waterproofing | $300 - $700 |
| Stainless Steel Liner | $3,000 - $6,500 |
| Partial Rebuild (above roofline) | $2,500 - $7,000 |
| Full Chimney Rebuild | $8,000 - $18,000 |
What pushes a Lynnwood job toward the top of its range is usually access: steep roofs, close neighboring homes, and the sticky creosote that takes longer to remove than dry flake. Whatever the number, it is written down before we start, and the photo record is yours when we finish.
Neighborhoods We Serve in Lynnwood

We cover all of Lynnwood, from the 1960s subdivision streets around Alderwood Manor to the split-levels near Brier and the ranch homes off 44th Ave W. Our crews are scheduled from the Seattle office and generally reach most Lynnwood homes within one to two business days for non-emergency work.
- Alderwood Manor
- Meadowdale
- Picnic Point
- North Lynnwood
- Brierwood
Service Area - Cities Near Lynnwood
We serve the surrounding Snohomish and north King County communities with the same camera-scan standard and written pricing. Our regular service area includes Mountlake Terrace, WA, Kenmore, WA, Edmonds, WA, and Bothell, WA. If you are just across a city line, call and we will confirm coverage.
Serving Lynnwood, WA - Our Local Coverage Area

We’re based in the Lynnwood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Cleaning in Lynnwood
Most cleaning, sweeping, and repointing does not require a permit in Lynnwood. Structural rebuilds or liner installations may, depending on scope, and Snohomish County fire code applies here rather than King County rules. We confirm code requirements before quoting major work.
We typically schedule Lynnwood sweeps within one to two business days. If you have water actively entering the house or visible smoke backing up, call (980) 580-8641 and we will prioritize the visit and advise you on what to do until we arrive.
Every Lynnwood job ends with a written service report, the camera footage and photos from inside your flue, a written warranty, and a copy of the price you approved. Nothing is verbal, and the photo record is yours to keep. Home to our full site for service details.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Lynnwood Customers Say
"Gas insert service done properly with the readings written down. The technician had the certification number printed on the paperwork."
- Bettina A."We were buying the house and needed a real inspection. The report had photographs, the standard it was done to, and a clear repair figure. The seller paid for the repair."
- Lorna D."They ran a camera down the flue and showed me the cracked tiles on a screen. The previous company had swept it twice and never mentioned it."
- Gregory F.





Before
After
Before
After