Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterFast, Reliable Chimney Cap & Crown Across Calabasas
Chimney cap and crown work in Calabasas is wildfire defense as much as weatherproofing. A typical cap replacement in Calabasas runs $380-$1,100 depending on flue count and material, while crown repair or coating lands between $450 and $1,400 on most homes here. If your cap is rusted, missing, or wrapped in a screen with gaps wider than your thumb, call us at (980) 580-8641. We’ll put it in writing before anyone touches your chimney.
Calabasas sits almost entirely inside a Very High Fire Hazard Severity Zone in the Santa Monica Mountains foothills. That’s not zoning jargon. It means California law requires a UL-listed spark arrestor on every chimney serving a fireplace or wood burning appliance in this city, and when the Woolsey Fire moved through these hills in 2018, Santa Ana winds drove embers into uncapped and poorly capped flues from the outside. A damaged chimney cap here is a documented ignition pathway. We build every inspection and every repair around that fact.
When we inspect a chimney in Calabasas, we do not shine a flashlight from the hearth and wave. Our crews run a camera down the flue, photograph the cap and crown from the roof, and show you every image before recommending a single dollar of work. Emberly Chimney Cleaners has operated that way since 2009 under the Haven Standard, and we write the price, scope, and warranty down before any repair begins. Corrine Halstead leads our operation with the same plain rule: if the camera doesn’t show it, we don’t quote it.
Why Emberly Chimney Cleaners Is Calabasas’s Preferred Chimney Cap & Crown Company
Calabasas homeowners ask us different questions than people in the valley floor communities. The question around here is not “does my chimney need a cap” but “is my cap actually ARRESTING sparks, or is it just keeping raccoons out.” The difference matters. Our Chimney Cap & Crown team has probably been asked that question a thousand times from Mulholland Highway to Las Virgenes Road.
We work in The Oaks, Calabasas Park, Calabasas Hills, and the estates off Mureau Road. Those neighborhoods have a particular housing profile: large custom and tract luxury homes built between roughly 1985 and 2005, most with factory built zero clearance prefab fireplaces in three, four, or five flue configurations. We know the spark arrestor hardware those homes shipped with. We know how it fails after 30 years of dry heat expansion along the 101 corridor. And we know what LA County Fire inspectors look for when a residence in this ZIP changes hands.
38,000 plus chimneys inspected and cleaned since 2009. Every one of them with a written price before work started and a photo record when it was done. Clause 4 of the Haven Standard requires that documentation, and it’s been our default since before regulators asked. Calabasas homeowners tend to read the three star reviews before calling anyone. We respect that. We’d rather show you the camera footage than give you a speech.
Our Chimney Cap & Crown Services in Calabasas
Cap Installation
A new cap is the cheapest insurance a Calabasas homeowner can buy against the next Santa Ana event. We install UL listed spark arrestor caps sized to your exact flue tile or factory built termination, and we photograph the install from the roof before we come down. Most installations in Calabasas run $380-$750 for a single flue, with multi flue jobs priced by flue count and cap type.
Cap Replacement
If your home was built in the late 80s or mid 90s in Calabasas, your original cap has survived 30 to 40 summers of dry heat expansion and the same number of cool winter cycles. We regularly replace spark arrestors with warped screening or corroded mounting straps on homes in The Oaks and along Park Granada. A replacement cap with new mounting hardware typically runs $400-$1,100 in Calabasas depending on whether it’s a single flue or a five flue custom termination.
Multi Flue Cap
Many Calabasas estates run three, four, or five flues to separate fireplace and furnace venting. A multi flue cap spans the crown and covers every termination at once, which changes both the geometry and the price. We source Famco and Olympia Chimney multi flue caps through Haven’s buying network and install them with the flashing and mounting detail required for wind exposure on a ridgeline. Expect $900-$2,400 for a proper multi flue cap on a Calabasas ridge home.
Crown Repair
A cracked or spalling chimney crown lets water into the masonry below, and Calabasas sees exactly enough winter rain to make that a slow, expensive problem. We remove failed crown material, rebuild the slope, and install a proper drip edge so water sheds away from the flue instead of into it. Crown repair in Calabasas typically runs $500-$1,200 for a standard single chimney, more when multiple flues share the top.
Crown Coating
For crowns that are still structurally sound but showing hairline cracks, we apply a Gelco crown coat rather than a full tear out. It seals the crown against moisture intrusion and buys years before rebuild is necessary. On Calabasas homes with multiple flues, we coat the entire crown span in a single visit. Plan $450-$900 for a typical crown coating here.
Custom Cap
Some Calabasas homes have chase tops that were built as one offs, or terminations that no standard cap fits. We measure, template, and order custom caps through Copperfield with the same UL listed mesh spec required by code. Custom work is priced from the template and is always written down as a firm quote before fabrication begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Calabasas
We stock and install materials from Famco, Olympia Chimney, DuraFlex, and Copperfield, sourcing through Haven’s network to keep Calabasas pricing honest. If your existing cap is a Famco or Olympia unit that’s rusted out, we can match the termination footprint without replacing the entire chase top. That speed matters when a pre listing deadline is a week out. Our parts runs cover Calabasas and the surrounding foothill communities daily, so the cap that gets ordered Tuesday is typically on your roof Thursday.
Common Chimney Cap & Crown Problems We See in Calabasas Homes
- Corroded 30 to 40 year old spark arrestors. Homes built in Calabasas between 1985 and 1995 shipped with factory screens that have now endured decades of dry heat expansion. The mesh warps, the gaps open, and an LA County Fire inspector will flag it as a violation the moment the property goes under contract.
- Santa Ana debris loading in uncapped flues. Chaparral leaf litter, ash, and fine dust get driven horizontally into chimneys during fall wind events. In The Oaks and other hillside communities, we pull enough dry fuel from uncapped flues to make the cap question answer itself.
- Spalling crowns on multi flue masonry chimneys. Large Calabasas estates often have a wide masonry crown covering several flues. When that crown spalls and the drip edge fails, water sits on the crown and works into every flue from the top down. Coating or rebuilding the crown stops the damage before liner work is necessary.
- Prefab terminations cracked by ridge line exposure. Homes along Stunt Road and the higher reaches of Calabasas take sustained wind and temperature swing that valley homes never see. Chase tops and factory terminations crack at the seams, and once water gets behind a prefab termination, it follows the chase down into the firebox framing.
Pricing for Chimney Cap & Crown in Calabasas, CA
Here is what we actually charge in Calabasas. Single flue cap installation: $380-$750. Cap replacement with new mounting hardware: $400-$1,100. Crown coating: $450-$900. Crown repair or rebuild: $500-$1,400. Multi flue cap on a custom or estate chimney: $900-$2,400. What moves the number is flue count, roof pitch, whether the existing termination can be reused, and whether the crown needs sealing or full reconstruction. Every quote is written before work starts. Every job includes a photo record on completion. Call (980) 580-8641 for an exact written estimate. That’s the only number we use.
We Also Serve Cities Near Calabasas
Our crews dispatch out of the Los Angeles office and serve Calabasas locally, so we are on the road to Chimney Cap & Crown in Calabasas every day the same way we cover Woodland Hills, West Hills, Canoga Park, and Agoura Hills. If you’re just over the 101 from Calabasas, same crew, same written price, same photo record.
Serving Calabasas, CA - Our Local Coverage Area
We’re based in the Calabasas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Chimney Cap & Crown in Calabasas
A factory built prefab in Calabasas has a metal termination and spark arrestor assembly that expands and contracts at a different rate than masonry, and after 30 years of Santa Ana heat cycles the seams and screens fail in ways a traditional flue does not. We inspect the termination for screen gaps, cracked chase covers, and separation at the flue collar, because those are the exact points where a wind driven ember gets in. Call (980) 580-8641 and we’ll camera the flue and photograph the termination before quoting anything.
Every five to seven years is honest for Calabasas, though a crown showing visible cracks or spalling needs attention immediately regardless of the calendar. Mild winters mean less freeze thaw than somewhere like the Northeast, but Santa Ana winds and dry heat cycle the crown material hard, and a multiple flue crown has more linear edges to fail. We write the current crown condition into every inspection report with photos, so you are deciding on evidence, not us guessing.
If the flues share a single termination footprint, a custom multi flue cap is usually the better long term answer for a 3 to 4 flue Calabasas home. Standard caps leave gaps between terminations on wide chase tops, and a gap is an ember entry point. We template the chase top, quote a Copperfield or Famco custom unit with UL listed mesh, and install it once instead of stacking four separate caps that fight each other for flashing. The written quote tells you the difference before you decide.
Warped or corroded spark arrestor screening on homes built between 1985 and 1995, flagged as a direct LA County Fire code violation by the buyer’s inspector and occasionally by the insurance underwriter. We replaced a corroded 1992 Olympia Chimney spark arrestor on a five flue custom home in The Oaks after a pre listing inspection flagged exactly that. Our techs fitted a multi flue cap with UL listed mesh across all flues, then coated the spalling crowns with Gelco. The home closed on schedule and passed the buyer’s Level 2 inspection with zero cap or crown deficiencies. If you’re listing in Calabasas, get the cap checked before it’s a closing table problem.
Because the cap and crown are doing their job 365 days a year even when the fireplace is cold. In a Very High Fire Hazard Severity Zone like Calabasas, the code requirement for a functioning UL listed spark arrestor does not depend on how often you burn. A deteriorated cap on a rarely used fireplace is still an ember catcher during a Santa Ana event. And an uncapped flue accumulates leaves and ash that become fuel. Annual inspection with camera documentation is the only way to prove the termination is actually intact. Call us for a quote, have the photos in your hands, and decide after you’ve seen the flue yourself.
Written by Corrine Halstead, Owner at Emberly Chimney Cleaners, serving Calabasas under the Haven Standard.