Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterFast, Reliable Chimney Cap & Crown Across Burleson
A chimney cap and crown replacement in Burleson typically runs $240-$680 for the cap itself and $650-$1,400 for crown repair or coating work, depending on whether you have a factory-built chase cover or a traditional masonry crown. Most jobs are completed in a single visit once we’ve measured the flue and documented the existing condition. If you live off Renfro Street, in Oak Valley, or anywhere else in Burleson, call (980) 580-8641 for a written estimate before you agree to anything.
We work throughout Burleson’s tract-home neighborhoods and the older masonry homes near historic downtown. The housing stock differs wildly between those two areas, and so does the right fix. A cap that works on a 2006 Heatilator in Parks at Panache won’t serve an original clay-tile chimney off Johnson Avenue. We measure first, quote in writing, and only then do the work.
Why Emberly Chimney Cleaners Is Burleson’s Preferred Chimney Cap & Crown Company
Burleson’s housing boom from the late 1990s through the 2000s gave us thousands of factory-built zero-clearance fireplaces, most sealed with builder-grade chase covers that were never designed to last this long. We’ve documented that failure pattern here more than anywhere else in Johnson County. Our Chimney Cap & Crown team works from measurements, photos, and flue geometry, not guesses. Every Burleson job includes a camera-scan inspection before we touch anything, and a documented photo record when we’re done. That’s Clause 4 of the Haven Standard, which we’ve kept on every job since 2009.
Corrine Halstead runs Emberly Chimney Cleaners with a simple rule: if it can’t be photographed and put in writing, it doesn’t get recommended. That’s why homeowners in Burleson who’ve been burned by flash-and-dash chimney companies tend to stick with us. You’ll see the crown cracks. You’ll see the rusted chase seam. You’ll get a written price, a written scope, and a written warranty before anyone climbs a ladder. No exceptions.
We also know how tight Burleson lots get. Side yards off Alsbury Boulevard, cul-de-sac roofs in Misty Meadows, steep pitches in Bailey Ranch. Our crews arrive with the right staging equipment for confined access, not just whatever fits in the truck.
Our Chimney Cap & Crown Services in Burleson
Cap Installation
If your Burleson home has no cap at all, rain, birds, and debris have a direct path into your flue. On factory-built units, we install stainless caps sized to the manufacturer’s listed termination, not a universal fit from a big-box shelf. On masonry chimneys, we measure the flue tile and install a cap with proper mesh sizing that won’t choke draft. Most cap installations in Burleson run $240-$480, including materials and a documented photo record.
Cap Replacement
Rusted, bent, or storm-damaged caps are the most common fix we see after hail season moves through Burleson. A replacement cap on a typical tract home off McAlister Road runs $260-$520. If the damage also includes the chase cover underneath, you’re realistically looking at $580-$980 combined. We replace, not patch. A patched cap fails the same way next spring.
Crown Repair
Masonry crowns in Burleson’s older homes crack for a specific reason: the Blackland Prairie clay under Johnson County expands and contracts enough to open hairline joints seasonally. On a home built before 1985 near downtown, a cracked crown isn’t a one-time fix if all you do is tuckpoint. We repair the crown, then coat it with a flexible waterproof membrane so movement doesn’t tear it open again. Crown repair in Burleson starts around $650 and runs to $1,100 depending on how far the damage has spread behind the brick veneer.
Crown Coating
For crowns that are structurally intact but showing surface cracking, coating is the right call. We use Gelco crown sealant, a product we’ve specified on Burleson masonry homes for years because it flexes with the Prairie clay movement. A standard crown coating runs $450-$750 in Burleson. It comes with a written warranty and photo documentation of the before and after.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Burleson
We stock and install caps, chase covers, and crown materials from Gelco, Famco, and Olympia Chimney. These are the same brands we’ve run on thousands of chimneys since 2009, and we keep common Burleson sizes in inventory so you’re not waiting on a warehouse out of state. If you’ve got a factory-built fireplace from Heatilator, Majestic, or similar, we match the manufacturer’s listed cap dimensions rather than forcing an adapter. A wrong-sized cap is a draft problem waiting to happen.
Common Chimney Cap & Crown Problems We See in Burleson Homes
- Builder-grade chase covers rusting through at the seam. On Burleson’s 1995-2012 tract homes, the original chase cover is usually thin galvanized steel with a folded seam. After 12-15 years of Texas hail, wind-driven rain, and freeze-thaw from the occasional ice storm, that seam opens up. Water pours directly onto the fireplace, rusting dampers and damaging firebox panels you won’t see until it’s too late.
- Blackland Prairie clay shifting masonry crowns. Homes near historic downtown Burleson sit on expansive clay that swells after spring rain and shrinks through summer drought. The cycle opens crown cracks that never truly close. A crown repair without a flexible coating fails again the following July. We see this exact pattern on original clay-tile flue liners throughout the downtown core.
- Shared chases cross-venting between homes. Many Burleson attached and closely-spaced zero-clearance homes were built with two flue terminations inside one chase. If one cap is missing or the crown between them is breached, a neighbor’s gas appliance can vent into your firebox instead of out the termination. Carbon monoxide doesn’t respect property lines.
- Chimney swifts and starlings nesting in uncapped flues. Burleson fireplaces sit idle 8-10 months a year. That’s enough time for migratory chimney swifts to build nests in an uncapped flue, and enough time for their droppings and debris to harden into a blockage. Removing a swift nest is a job for a professional, not a DIY morning with a wire brush.
A Shared-Flue Problem We Fixed Off Renfro Street
Last March our crew was called to a house off Renfro Street in Burleson’s Oak Valley subdivision. The home, built in 2004, had a Heatilator zero-clearance unit with a rusted chase cover and a cracked, spalling crown. When we pulled the old cap, we found an adjacent neighbor’s water heater flue shared the same chase. A builder shortcut we see all the time. We fabricated a custom multi-flue cap from sheet stainless to vent both appliances separately, then coated the crown with Gelco and replaced the chase top. The homeowner had no idea the two flues were intertwined. Without that fix, the neighbor’s carbon monoxide could have been re-entrained on a windy day. This is why we don’t quote cap work in Burleson from a photo alone. We need to see the chase geometry.
Pricing for Chimney Cap & Crown in Burleson, TX
Here’s what Burleson homeowners can expect to pay, based on the work we’ve done across Oak Valley, Misty Meadows, Parks at Panache, and the older homes near downtown:
- Standard cap installation (factory-built or masonry): $240-$480
- Cap replacement with new stainless steel cap: $260-$520
- Chase cover replacement (wind-damaged or rusted): $580-$980
- Custom multi-flue cap for shared chases: $450-$900, fabricated to your chase dimensions
- Crown repair with waterproof coating: $650-$1,100
- Crown coating only (structurally sound crown): $450-$750
Every quote includes the written scope, the written warranty, and the photo record. We don’t charge extra for documentation. If you bring us a written competitor estimate, we’ll give you a free second opinion at no cost. Call (980) 580-8641 to schedule a camera inspection and written quote.
We Also Serve Cities Near Burleson
Our crews cover the entire southern Dallas-Fort Worth metro, so we’re regularly in Burleson and the surrounding communities. That includes Mansfield, Arlington, Cleburne, and Fort Worth. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, with local crews dispatched directly to Burleson neighborhoods.
Serving Burleson, TX - Our Local Coverage Area
We’re based in the Burleson area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Chimney Cap & Crown in Burleson
A chimney cap sits on top of the flue opening and keeps rain, animals, and debris out. A chase cover is the flat metal top that seals the entire chase, the framed box that encloses a factory-built fireplace. On Burleson’s 1995-2012 tract homes, the chase cover usually fails first because it’s a builder-grade sheet metal piece exposed to full weather. Replacing the cap without addressing a rusted chase cover is a waste of money. Call (980) 580-8641 and we’ll show you photos of both before quoting anything.
Yes, but it requires a custom multi-flue cap sized to both terminations, and we have to inspect the chase interior first. On Burleson attached homes, we regularly find two flues terminating through one chase with a single cover. If one flue is uncapped or the crown between them is breached, combustion gases can cross into the other fireplace. We fabricate the cap from sheet stainless to keep each flue venting independently. Expect to pay $450-$900 for the fabricated cap, depending on chase dimensions.
Because the repair didn’t account for Burleson’s Blackland Prairie clay. The soil under Johnson County expands when wet and contracts when dry, and that movement transfers up through the chimney. A rigid mortar patch cracks again within a season. The fix is a flexible crown coating, like Gelco, over a properly repaired crown. That’s the only method we’ve seen hold up on Burleson masonry chimneys over multiple freeze-thaw and drought cycles.
Yes, and arguably more than someone who burns regularly. An unused flue is a nesting cavity for chimney swifts, and Burleson sits on their migration route. Uncapped flues also let rain into a firebox that never gets hot enough to dry out. That’s how you get rusted dampers, cracked refractory panels, and the exact conditions that make a fireplace unsafe when you do finally light it. A cap is cheap compared to a firebox rebuild. Call (980) 580-8641 for a written quote.
It starts with roof access planning. On Burleson homes with 8/12 pitches and 5-foot side yards, we bring staging equipment sized to fit a narrow setback, and our techs are trained on confined-access ladder work. The actual replacement is straightforward once we’re up: remove the old cap, measure the flue or termination, install the correct stainless cap, and photograph everything for your record. Most steep-roof cap replacements in Burleson take about an hour on the roof, and we’ll text you when the crew is on the way.
Get Your Chimney Cap & Crown Inspected Before the Next Hail Season
Burleson’s hail and ice cycles are rough on chimney tops. If you haven’t looked at your cap and crown since you bought the house, or if you bought between 2015 and 2025 and inherited whatever the original builder installed, now’s the time. We’ll camera-scan the flue, photograph the chase cover and crown, and put everything in writing before any work starts. One visit, no pressure, documented record. Call (980) 580-8641 to book your inspection.
Written by Corrine Halstead, Owner at Emberly Chimney Cleaners, serving Burleson with camera-documented inspections and written pricing since 2009.